Home/ Physics/ Chapter 14 — Semiconductor Electronics
Class 12 Physics · Chapter 14 · Rebuilt from NCERT

Semiconductor Electronics

From silicon atoms to the chip in your phone — with animated p-n junction formation, interactive diode V-I simulator, 3D doping visualization, rectifier waveform animations, and 20+ real-life examples.

8Sections
20+Real-life Examples
9Diagrams
1Simulator
The Big Picture

🗺️ How Everything Connects

Before diving in, here's the entire chapter on one page. This is your mental map — every topic is a link in this chain.

Metals vs Semiconductors Intrinsic Si/Ge Extrinsic (n & p type) p-n Junction Diode (bias) Rectifier (half/full) Filters & DC Doping Threshold voltage "How do we control current with semiconductors?" Doping creates n-type & p-type · junction forms diode
Key Takeaway

Semiconductors have intermediate conductivity — controllable by doping and temperature. Pure (intrinsic) Si/Ge has equal electrons and holes. Adding pentavalent/trivalent dopants creates n-type/p-type. Joining p and n creates a diode that conducts ONE way. Diodes rectify AC to DC — the foundation of every power supply and electronic circuit.

Section 01

Introduction — Why Semiconductors?

14.1The Electronics Revolution

Before the 1950s, all electronics used vacuum tubes — glass bulbs with heated filaments, large, fragile, and power-hungry. Then came the transistor (1947, Bardeen, Brattain, Shockley) — a tiny solid-state device made of semiconductors. Today, a single chip smaller than your fingernail contains billions of transistors.

PropertyVacuum TubeSemiconductor Device
SizeCentimeters (bulb-sized)Nanometers (chip-scale)
PowerHigh (needs heater)Very low
VoltageHundreds of voltsA few volts
LifetimeLimited (burnout)Very long
ReliabilityFragileVery high

Even older CRTs (cathode-ray tubes) in old TVs and monitors are now replaced by LCD/OLED displays powered by solid-state transistors. Before the physics was fully understood, a natural galena (PbS) crystal with a metal point contact was already used as a radio detector!

Real Life Connect — Where Semiconductors Live
  • Every computer, phone, TV: Billions of transistors per chip, all made from semiconductors (mostly silicon).
  • Solar cells: Photovoltaic panels are large p-n junctions that convert sunlight directly to electricity.
  • LED lights: Light-emitting diodes — semiconducting materials that emit light when current flows.
  • Lasers: Laser diodes in DVD players, fiber-optic communication, barcode scanners.
  • Camera sensors: CMOS and CCD image sensors — millions of photodiodes per chip.
  • Power electronics: Rectifier diodes and IGBTs in every power supply, charger, and electric vehicle.
  • Medical devices: Pacemakers, ultrasound transducers, X-ray detectors — all rely on semiconductor electronics.
  • Industrial control: Sensors, microcontrollers, motor drivers — the internet of things (IoT) runs on chips.
Key Takeaway

Semiconductor devices replaced vacuum tubes — smaller, cheaper, more reliable, lower power. Today's world runs on silicon. All modern electronics depend on understanding p-n junctions, diodes, and transistors.

Section 02

Classification of Metals, Conductors, and Semiconductors

14.2Conductivity — Three Broad Classes

Classification by Resistivity/Conductivity

Metals: Very low resistivity (high conductivity)

ρ ~ 10⁻² – 10⁻⁸ Ω·m · σ ~ 10² – 10⁸ S/m

Semiconductors: Intermediate

ρ ~ 10⁻⁵ – 10⁶ Ω·m · σ ~ 10⁵ – 10⁶ S/m

Insulators: Very high resistivity (low conductivity)

ρ ~ 10¹¹ – 10¹⁹ Ω·m · σ ~ 10⁻¹¹ – 10⁻¹⁹ S/m

Note: Ranges are indicative — some materials may fall outside. Resistivity is not the only criterion.

Types of Semiconductors

Elemental: Si (silicon), Ge (germanium) — pure elements

Compound (inorganic): CdS, GaAs, CdSe, InP — combinations

Organic: Anthracene, doped phthalocyanines

Organic polymers: Polypyrrole, polyaniline, polythiophene

Most current devices use Si or Ge (elemental) and GaAs (compound). Organic semiconductors are an emerging field (OLED displays!).

Classification by Energy Bands

V1 · Energy band diagrams — metals, insulators, semiconductors Metals (overlapping bands) Conduction Valence Eg ≈ 0 (overlap) Insulators (large gap) Conduction (empty) Valence (filled) Eg > 3 eV No electrons can jump Semiconductors (small gap) Conduction Valence Eg < 3 eV Few electrons can jump (thermal) Band gap Eg determines material class C (diamond): 5.4 eV · Si: 1.1 eV · Ge: 0.7 eV · Sn: 0 eV (metal!) Group IV elements: as Eg decreases, material becomes more conductive
Key Concept: Energy Bands

Valence band: Energy levels of valence electrons (outer shell)

Conduction band: Higher energy levels where electrons can move freely

Band gap Eg: Energy difference between the top of valence band (E_v) and bottom of conduction band (E_c)

Metals: Eg ≈ 0 (bands overlap). Conduct even at 0 K.

Insulators: Eg > 3 eV. No electrons in conduction band even at room temperature.

Semiconductors: Eg < 3 eV. Some electrons are thermally excited to conduction band at room temperature.

Real Life Connect
  • Silicon (Eg = 1.1 eV): The workhorse of all electronics — ideal gap for room-temperature operation.
  • Germanium (Eg = 0.7 eV): Used in early transistors and now in high-speed infrared detectors.
  • GaAs (Eg = 1.4 eV): Used in high-frequency amplifiers (mobile phones), solar cells, and LEDs.
  • GaN (Eg = 3.4 eV): Used in blue LEDs (Nobel Prize 2014) and power electronics.
  • Diamond (Eg = 5.4 eV): Excellent insulator, but can be doped to become a semiconductor (future high-power electronics).
  • Tin (Eg = 0 eV): A metal — one "step" below Si in the periodic table, but a whole different class!
Common Mistake

Mistake: "Semiconductors have no conductivity."
Correction: They DO conduct — just not as much as metals. At room temperature, pure Si has ~10¹⁰ free electrons per cm³ — enough for measurable conductivity.

Mistake: "Semiconductors are always n-type or p-type."
Correction: Pure (intrinsic) semiconductors are neither! They become n- or p-type only after doping with impurities.

Key Takeaway

Three classes by band gap: metals (Eg ~ 0), insulators (Eg > 3 eV), semiconductors (Eg 0.2–3 eV). Silicon's 1.1 eV bandgap is ideal for room-temperature electronics. Conductivity is tunable via doping and temperature.

Section 03

Intrinsic Semiconductor

14.3Pure Silicon and Germanium

Si and Ge have a diamond-like crystal structure — each atom is bonded to 4 nearest neighbors by covalent bonds (sharing electrons).

Crystal Structure

Si and Ge are tetravalent (4 valence electrons). Each atom shares 1 electron with each of its 4 neighbors, forming 4 covalent bonds.

Lattice constants: Si = 5.43 Å, Ge = 5.66 Å, C (diamond) = 3.56 Å

At 0 K, all electrons are locked in bonds → no free electrons → semiconductor behaves as insulator.

V2 · Si/Ge crystal lattice — 2D schematic +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 Each atom shares 4 electrons with neighbors — covalent bonds 2D representation of Si/Ge lattice (+4 = core + 4 valence electrons)
Hole-Electron Pair Generation

At T > 0 K, thermal energy can break a covalent bond. The electron becomes free (conduction electron), leaving behind a hole (vacancy with effective positive charge +e).

For intrinsic semiconductor: n_e = n_h = n_i (intrinsic carrier concentration)

Both electrons and holes contribute to conduction. Total current: I = I_e + I_h

V3 · Thermal generation of electron-hole pair +4 +4 +4 +4 +4 +4 +4 hole +4 +4 +4 +4 +4 +4 +4 +4 +4 +4 🔥 T > 0 K − free e⁻ + hole Thermal energy breaks a covalent bond → electron + hole In intrinsic semiconductor: number of electrons = number of holes (n_e = n_h)
Key Relations for Intrinsic Semiconductor

n_e = n_h = n_i (carrier concentration)

Both electrons (negative) and holes (positive) contribute to current:

I = I_e + I_h

Direction of current:

  • Electron current: opposite to electron flow (i.e., along E-field)
  • Hole current: along hole flow (i.e., along E-field)
  • Both contribute to conventional current!

Generation ↔ Recombination equilibrium: at steady state, generation rate = recombination rate.

Real Life Connect
  • Pure Si wafers (99.9999% pure) — the starting material for all chips. Made by zone refining (repeated melting).
  • Temperature sensors: A thermistor (temperature-sensitive resistor) uses intrinsic semiconductor — conductivity rises with T.
  • Photoconductors: When light shines on intrinsic semiconductor, extra electron-hole pairs are created, increasing conductivity — basis of photodetectors.
  • Silicon photodiodes: Even in reverse bias (undoped region), intrinsic electron-hole pairs are created by light.
  • Sunlight detection: Solar cells are made from semiconductors where photons create electron-hole pairs.
Why Are There Always Equal Numbers of Electrons and Holes?

Because when a bond breaks, one electron leaves its valence site and one hole is left behind. The process is inherently paired — the same thermal energy creates both. So n_e = n_h for pure semiconductors. This balance holds until we add impurities (doping).

Key Takeaway

Intrinsic semiconductor: pure Si/Ge. Each atom shares 4 valence electrons with neighbors (covalent bonds). Thermal energy creates electron-hole pairs. n_e = n_h = n_i. Both carriers contribute to current. At 0 K, behaves as insulator.

Section 04

Extrinsic Semiconductor

14.4Doping — The Secret to Modern Electronics

Pure silicon has too few free carriers for practical devices. Solution: add a tiny amount of impurity — a few parts per million — to dramatically increase conductivity. This is doping.

Doping Basics

Doping: Deliberate addition of small amounts of impurity atoms to a pure semiconductor.

Dopant: The impurity added.

Requirements for doping to work:

  • Dopant size ≈ Si/Ge atom size (so it fits into the lattice)
  • Dopant forms same crystal structure
  • Only a few ppm needed — the lattice structure is preserved

n-type Semiconductor (Pentavalent Dopant)

n-type Semiconductor

Dopant: Pentavalent (5 valence electrons) — P, As, Sb

4 of the 5 valence electrons form covalent bonds with neighboring Si atoms. The 5th electron is very weakly bound (ionization energy only ~0.01–0.05 eV) and easily becomes a free conduction electron.

Called "donor" impurity because it "donates" a free electron.

Result: n_e >> n_h (electrons are majority carriers, holes minority).

V4 · n-type and p-type semiconductors n-type (doped with P, As, Sb) +4 +4 +5 donor +4 +4 − 5th e⁻ free n_e >> n_h (majority electrons) Donor level just below E_c (0.01–0.05 eV) p-type (doped with B, Al, In) +4 +4 +3 acceptor +4 +4 + hole n_h >> n_e (majority holes) Acceptor level just above E_v (0.01–0.05 eV) Dopant (ppm level) increases conductivity enormously Mass action law: n_e × n_h = n_i² (always)

p-type Semiconductor (Trivalent Dopant)

p-type Semiconductor

Dopant: Trivalent (3 valence electrons) — B, Al, In

3 of the 4 covalent bonds form normally. The 4th bond has a missing electron = a hole. The dopant is called an acceptor — it can accept an electron from a neighboring bond.

Result: n_h >> n_e (holes are majority carriers, electrons minority).

Mass Action Law

For any extrinsic semiconductor (n or p):

n_e × n_h = n_i² (always, in thermal equilibrium)

Where n_i = intrinsic carrier concentration.

So if we dope with donors (increasing n_e), the hole count n_h must decrease to maintain the product.

Crystal remains electrically neutral: donor ions (positive) + extra electrons (negative) balance out.

Numerical Example (from NCERT)

Example 14.2 — Pure Si doped with As

Si has 5×10²⁸ atoms/m³. Doped with 1 ppm As (pentavalent):

N_D = 5×10²⁸ × 10⁻⁶ = 5×10²² donors/m³

Since N_D >> n_i (~10¹⁶), we get: n_e ≈ N_D = 5×10²² m⁻³

Using n_e n_h = n_i² = (1.5×10¹⁶)² = 2.25×10³²:

n_h = 2.25×10³² / 5×10²² ≈ 4.5×10⁹ m⁻³

So n_e / n_h ≈ 10¹³ — electrons are 13 orders of magnitude more abundant than holes!

Real Life Connect
  • All transistors use n-type and p-type semiconductors — you can't make a diode or transistor without both.
  • Solar cells: p-n junction with n-type on top — sunlight creates electron-hole pairs that are separated by the junction.
  • LEDs: n-type and p-type materials chosen so that electron-hole recombination emits specific colors.
  • Thermoelectric coolers: Use n-type and p-type pairs to pump heat — Peltier effect.
  • Transparent conductors: Indium tin oxide (ITO) used in touchscreens is heavily n-doped to be both transparent and conductive.
  • Organic semiconductors: Emerging field — organic LEDs (OLEDs) in high-end displays use doped organic layers.
Common Mistake

Mistake: "n-type is negatively charged."
Correction: n-type is electrically NEUTRAL. The donor atom becomes positive when it donates an electron, but that positive charge balances the added electron. Overall charge = 0.

Mistake: "n-type has more electrons than holes only because of doping."
Correction: True, but there's a subtlety — the number of intrinsic (thermally generated) holes DECREASES when you add donors. The product n_e × n_h is fixed at n_i².

Key Takeaway

Doping (ppm level) dramatically increases conductivity. n-type (pentavalent dopant): electrons majority. p-type (trivalent dopant): holes majority. Mass action law: n_e × n_h = n_i². Crystal remains neutral.

Section 05

p-n Junction

14.5Where Two Worlds Meet

A p-n junction is formed by joining p-type and n-type semiconductor materials. This is the basic building block of diodes, transistors, LEDs, solar cells — nearly all semiconductor devices.

How to Make a p-n Junction

Take a thin p-type Si wafer. Dope one side with pentavalent (n-type) impurity. The junction forms at the boundary.

Note: You CANNOT just glue p-type and n-type slabs — the atomic-scale contact requires proper crystal continuity (Example 14.3 in NCERT).

Formation — Two Processes: Diffusion and Drift

V5 · p-n junction formation — diffusion → depletion → equilibrium Step 1: Before contact p-type (holes) n-type (electrons) Step 2: Diffusion begins p-type n-type holes → n · electrons → p Step 3: Depletion region forms p-type − ions (acceptor) DEPLETION n-type + ions (donor) E Step 4: Equilibrium p n V₀ ≈ 0.3V (Ge) E-field from n to p Barrier V₀ = 0.7V (Si) Diffusion = drift at equilibrium → no net current
Depletion Region and Barrier Potential

Depletion region: A thin layer (~10⁻⁷ m) at the junction where free charges have diffused away, leaving behind immobile ions.

p-side edge: negative ions (from acceptor atoms that gained electrons)

n-side edge: positive ions (from donor atoms that lost electrons)

Electric field: Points from n (positive) to p (negative)

Barrier potential V₀: The potential difference across the depletion region. Typical values:

  • Si: V₀ ≈ 0.7 V
  • Ge: V₀ ≈ 0.3 V
Two Currents at Equilibrium

Diffusion current: Due to concentration gradient — holes p→n, electrons n→p. Direction: p→n internally.

Drift current: Due to the E-field — minority carriers swept across junction. Direction: n→p internally (opposite to diffusion).

At equilibrium: diffusion = drift → net current = 0.

Real Life Connect
  • Every diode — the p-n junction is the fundamental device. All LEDs, rectifiers, solar cells, photodetectors use junctions.
  • Junction field-effect transistors (JFET) — use the depletion region to control current.
  • Semiconductor sensors — depletion width changes with external conditions (temperature, pressure, light).
  • Photodiodes and solar cells — light creates electron-hole pairs in the depletion region, generating current.
  • Thermal imaging — junction temperature affects barrier potential and current.
Key Takeaway

p-n junction formation: diffusion creates depletion region + electric field. Barrier potential V₀ (0.7V Si, 0.3V Ge). Equilibrium: diffusion current = drift current, net current = 0. This is the foundational structure of all semiconductor devices!

Section 06

Semiconductor Diode — Forward & Reverse Bias

14.6A One-Way Valve for Current

A diode is a p-n junction with metallic contacts. Its key property: conducts current easily in ONE direction (forward), blocks it in the other (reverse).

Diode Symbol

Triangle pointing from p to n:

p →|— n

Arrow indicates direction of conventional current in forward bias.

V6 · Diode under forward vs reverse bias Forward bias (conducts) p-type narrow n-type + terminal connects to p (positive) − terminal connects to n (negative) Large current (mA) Reverse bias (blocks) p-type wide n-type − connects to p + connects to n Tiny leakage current (μA) Forward: barrier (V₀−V) reduced → current flows freely Reverse: barrier (V₀+V) increased → current blocked Forward: minority carrier injection + diffusion current Reverse: only drift current from minority carriers

Forward Bias — Conducts

Forward Bias

Setup: p-side connected to + terminal of battery, n-side to − terminal.

Effect: Applied voltage opposes barrier potential → effective barrier becomes (V₀ − V) → depletion region narrows → electrons/holes easily cross junction.

Result: Forward current flows, typically milliamperes (mA).

Threshold voltage: Below this voltage, current is small. Above it, current rises steeply. Threshold ≈ 0.7 V (Si) or 0.2–0.3 V (Ge).

Reverse Bias — Blocks

Reverse Bias

Setup: n-side connected to + terminal, p-side to − terminal.

Effect: Applied voltage adds to barrier → effective barrier becomes (V₀ + V) → depletion region widens → diffusion current suppressed.

Result: Only tiny drift current (μA) flows due to minority carriers. This is called the reverse saturation current — nearly independent of applied voltage.

Breakdown: At very high reverse bias (V_br), current increases sharply. If not limited, the diode may be destroyed.

V7 · Diode V-I characteristic (animated simulation) V (forward →) → I → 0 Forward (mA scale) 0.2 0.4 0.6 0.8 exponential V_th (0.7V Si) Reverse (μA scale) −0.2 −0.4 −0.6 reverse saturation current (μA) V_br (breakdown) Diode V-I characteristic — one-way conduction

Diode Simulator — see how current changes with voltage and temperature

Current through diode
~0.35 mA
Bias state
Forward (below threshold)
Diode Current Equation (Shockley)

I = I₀ (e^(eV/kT) − 1)

Where I₀ = reverse saturation current, k = Boltzmann constant, T = temperature.

For forward bias (V >> kT/e): I ≈ I₀ e^(eV/kT) — exponential rise.

For reverse bias (V << 0): I ≈ −I₀ — nearly constant small negative current.

Real Life Connect
  • Rectifiers in power supplies: Convert AC to DC — every charger, laptop, TV uses diodes.
  • LEDs: Forward-biased diodes that emit light when electrons recombine with holes.
  • Solar cells: Reverse-biased p-n junctions that generate current when light hits.
  • Photodiodes: Detect light — reverse current proportional to light intensity.
  • Zener diodes: Operated in breakdown region for voltage regulation.
  • Protection diodes: Prevent reverse polarity damage to circuits (e.g., "flyback" diodes in motors).
  • Varactor diodes: Variable capacitance with reverse voltage — used in tuning circuits.
Exam Trap

Trap: "Diode conducts in both directions."
Correction: NO — a regular diode conducts easily only in forward bias. In reverse bias, only a tiny leakage current (μA) flows. The diode is fundamentally a one-way valve.

Trap: "Threshold voltage is the same for all diodes."
Correction: It depends on material: Si ≈ 0.7 V, Ge ≈ 0.2–0.3 V. Also depends on temperature and current level (slightly).

Key Takeaway

Diode = p-n junction with one-way conduction. Forward bias: barrier reduced (V₀−V), current flows (mA). Reverse bias: barrier increased (V₀+V), only tiny drift current (μA). Threshold: 0.7 V Si, 0.2 V Ge. Shockley equation: I = I₀(e^(eV/kT) − 1).

Section 07

Application — Diode as Rectifier

14.7AC → DC — The Most Important Application

A rectifier converts AC (which reverses direction) to DC (which flows one way). It uses the one-way property of diodes.

Half-Wave Rectifier

Half-Wave Rectifier

Circuit: AC source → transformer (optional) → diode → load resistor R_L

Operation:

  • Positive half-cycle of AC: diode forward-biased → current flows → output appears
  • Negative half-cycle: diode reverse-biased → current blocked → no output

Result: Pulsating DC output — only during positive half-cycles

Output frequency = input frequency (50 Hz in India)

Efficiency: 40.6% (only half the AC wave is used)

V8 · Half-wave rectifier — waveforms Circuit ~ ▶| R_L Input AC + − time → Output (pulsating DC) time → Only positive half cycles appear

Full-Wave Rectifier

Full-Wave Rectifier (Centre-tap)

Circuit: Centre-tapped transformer + 2 diodes (D₁, D₂) + load R_L

Operation:

  • Positive half-cycle (A positive, B negative): D₁ conducts, D₂ blocked → current flows via D₁
  • Negative half-cycle (A negative, B positive): D₁ blocked, D₂ conducts → current flows via D₂
  • In both cases, current through load R_L is in the same direction!

Result: Both half-cycles used → smoother DC output

Output frequency = 2× input frequency (100 Hz for 50 Hz input)

Efficiency: 81.2% (double the half-wave)

Alternative: Bridge rectifier uses 4 diodes but no centre-tap.

V9 · Full-wave rectifier — waveforms Circuit AC primary secondary (CT) D₁▶| D₂▶| R_L Input AC Output (both halves) All positive humps — smoother DC
Capacitor Filter (from NCERT)

A capacitor connected in parallel with R_L smooths the pulsating DC.

During peaks: Capacitor charges to peak voltage.

Between peaks: Capacitor discharges slowly through R_L, filling in the "gaps."

Time constant τ = R_L·C — larger = smoother output.

Output is closer to peak voltage — nearly steady DC!

Real Life Connect
  • Every electronic device that plugs into AC mains uses a rectifier — phones, laptops, TVs, kitchen appliances.
  • USB chargers: AC (220V) → transformer → rectifier → DC (5V) → USB output.
  • Solar panels: Produce DC directly, but grid-tied systems convert to AC and back — rectifiers everywhere.
  • Electric vehicle chargers: Rectify AC to DC to charge the battery.
  • Welding equipment: Uses rectifiers to convert AC to DC for stable arcs.
  • HVDC transmission: Rectifiers convert AC to high-voltage DC for long-distance transmission — less loss than AC!
  • Battery chargers: Need DC — rectifiers essential.
Why is DC Needed?

Most electronic circuits (ICs, microprocessors, LEDs, batteries) require DC. AC is great for transmission (easy to step up/down via transformers), but devices need steady DC to operate. The rectifier is the bridge between AC grid and DC electronics.

Key Takeaway

Rectifier: AC → DC using diode's one-way property. Half-wave: 1 diode, uses positive half-cycle, 40.6% efficiency. Full-wave: 2 diodes + centre-tap (or 4 in bridge), uses both halves, 81.2% efficiency. Capacitor filter smooths output to nearly steady DC. Universal in all power supplies!

Practice

📝 Solved Examples from NCERT

📋 NCERT Example 14.1

Q1. C, Si, and Ge have the same lattice structure. Why is C (diamond) an insulator while Si and Ge are intrinsic semiconductors?

Reasoning 1 Mark

All three have 4 valence electrons. The energy to free an electron depends on which orbit those electrons are in.

Energy gaps 1 Mark

C (diamond): Eg = 5.4 eV (electrons in n=2 orbit — tightly bound)

Si: Eg = 1.1 eV (n=3 orbit)

Ge: Eg = 0.7 eV (n=4 orbit)

The valence electrons are in higher n orbits for Ge and Si — easier to free.

Conclusion 1 Mark

For C, thermal energy at room temperature (0.026 eV) is too small to jump the 5.4 eV gap → effectively insulator. For Si/Ge, gap is small enough → some electrons jump → intrinsic semiconductor.

C: Eg = 5.4 eV (insulator). Si: 1.1 eV. Ge: 0.7 eV (semiconductors).
📋 NCERT Example 14.2

Q2. Pure Si crystal has 5×10²⁸ atoms/m³. Doped by 1 ppm of pentavalent As. Find n_e and n_h. Given n_i = 1.5×10¹⁶ m⁻³.

Donor concentration ½ Mark

N_D = 5×10²⁸ × 10⁻⁶ = 5×10²² m⁻³

Electron concentration ½ Mark

Since N_D >> n_i, we have n_e ≈ N_D = 5×10²² m⁻³

Hole concentration 1 Mark

n_e × n_h = n_i² = (1.5×10¹⁶)² = 2.25×10³²

n_h = 2.25×10³² / 5×10²² = 4.5×10⁹ m⁻³

Check ½ Mark

n_e / n_h = 10¹³ — electrons dominate by 13 orders of magnitude!

n_e ≈ 5×10²² m⁻³, n_h ≈ 4.5×10⁹ m⁻³ (n-type)
📋 NCERT Example 14.3

Q3. Can we take a p-type semiconductor slab and physically join it to an n-type slab to get a p-n junction?

Answer ½ Mark

NO!

Reason 1½ Marks

Even the flattest slab has surface roughness much larger than atomic spacing (~2–3 Å). Continuous contact at the atomic level is impossible.

The gap would act as a discontinuity — charge carriers would have to tunnel across a vacuum/air gap, which doesn't form a proper junction. The device would have poor electrical properties and not behave as a diode.

How junctions are actually made 1 Mark

By diffusing dopant atoms into one side of a single crystal (e.g., heating phosphorus onto a p-type wafer). Or by epitaxial growth of n-type on p-type. The lattice must be continuous!

No — atomic-level continuity required. Use diffusion or epitaxy, not physical joining.
📋 NCERT Example 14.4

Q4. From the given Si diode V-I curve: at I = 20 mA, V = 0.8 V; at I = 10 mA, V = 0.7 V. Find forward resistance. Also find reverse resistance at V = −10 V, I = −1 μA.

Forward resistance 1 Mark

r_f = ΔV / ΔI = (0.8 − 0.7) / (20 − 10) mA

= 0.1 V / 10 mA = 0.1 / 10×10⁻³ = 10 Ω

Reverse resistance 1 Mark

r_r = V / I = −10 V / (−1 μA)

= 10 / 10⁻⁶ = 10⁷ Ω = 10 MΩ

Comment ½ Mark

Forward: 10 Ω. Reverse: 10 MΩ. That's a ratio of 1,000,000:1 — that's how the diode acts as a one-way valve.

r_f = 10 Ω, r_r = 10 MΩ
📋 3 Marks

Q5. In a half-wave rectifier, input frequency is 50 Hz. What is the output frequency? What if full-wave?

Half-wave 1 Mark

One pulse per input cycle → output frequency = input frequency = 50 Hz

Full-wave 1 Mark

Two pulses per input cycle → output frequency = 2 × 50 = 100 Hz

Note 1 Mark

Higher output frequency means less ripple → easier to filter → smoother DC. Full-wave is preferred in most applications.

Half-wave: 50 Hz. Full-wave: 100 Hz.
📋 3 Marks

Q6. A silicon diode is forward biased at 0.75 V. If I₀ (saturation current) = 10⁻⁸ A and kT/e = 0.026 V at 300 K, find the current.

Shockley equation ½ Mark

I = I₀ (e^(eV/kT) − 1)

Exponent 1 Mark

eV/kT = 0.75 / 0.026 ≈ 28.85

e^28.85 ≈ 3.4 × 10¹²

Current 1 Mark

I ≈ I₀ × e^(eV/kT) = 10⁻⁸ × 3.4×10¹² = 3.4×10⁴ A

Whoa — that's huge! But real diodes have series resistance that limits current. Still, it shows exponential sensitivity: 0.75 V gives vastly more current than 0.70 V.

Insight ½ Mark

This is why the diode's forward voltage is nearly "constant" at ~0.7 V — small voltage changes cause huge current changes. Real diodes have parasitic resistances that limit actual current.

I ≈ 3.4×10⁴ A (theoretical max — real current limited by R_series)
📋 3 Marks

Q7. Distinguish between intrinsic and extrinsic semiconductors.

Intrinsic 1½ Marks

Pure semiconductor (Si or Ge). No impurities. n_e = n_h = n_i. Conductivity is low (only from thermal generation). Depends strongly on temperature. Behaves as insulator at 0 K.

Extrinsic 1½ Marks

Doped with small amount of impurity (pentavalent or trivalent). Conductivity greatly increased. Majority carriers (electrons for n-type, holes for p-type) dominate. Conductivity depends on doping level. Much more useful for devices.

Intrinsic: pure, n_e = n_h, low conductivity. Extrinsic: doped, majority + minority carriers, high conductivity.
Quick Reference

📐 Complete Formula Sheet

Chapter 14 — All Formulas on One Page

Conductivity
σ = 1/ρ (S/m)
Resistivity
ρ = 1/σ (Ω·m)
Intrinsic Carrier Concentration
n_e = n_h = n_i
Mass Action Law
n_e × n_h = n_i²
n-type semiconductor
n_e >> n_h (donor dopants P, As, Sb)
p-type semiconductor
n_h >> n_e (acceptor dopants B, Al, In)
Barrier Potential
V₀ ≈ 0.7 V (Si) · 0.3 V (Ge)
Forward Bias Barrier
Effective barrier = V₀ − V
Reverse Bias Barrier
Effective barrier = V₀ + V
Shockley Equation
I = I₀(e^(eV/kT) − 1)
Thermal Voltage
kT/e ≈ 0.026 V at 300 K
Dynamic Resistance
r_d = ΔV/ΔI
Half-wave Rectifier
f_out = f_in, efficiency ≈ 40.6%
Full-wave Rectifier
f_out = 2 f_in, efficiency ≈ 81.2%
Filter Time Constant
τ = R_L · C
Energy Band Gaps (300 K)
Si: 1.1 eV · Ge: 0.7 eV · C: 5.4 eV

📖 Notation Key

n_e, n_hElectron, hole concentration (m⁻³)
n_iIntrinsic carrier concentration
N_D, N_ADonor, acceptor concentration
V₀Barrier potential
V_thThreshold (cut-in) voltage
I₀Reverse saturation current
kT/eThermal voltage (≈0.026 V at 300 K)
E_gEnergy band gap
r_dDynamic resistance
ρ, σResistivity, conductivity
Test Yourself

✍️ MCQ Practice

Score: 0 / 12
New Pattern

🎯 Assertion–Reason

(A) Both true, R explains A. (B) Both true, R does NOT explain A. (C) A true, R false. (D) A false, R true.

Score: 0 / 6