Home/ Physics/ Chapter 15 — Communication Systems
Class 12 Physics · Chapter 15 · Legacy NCERT

Communication Systems

From Marconi's first radio signal to 5G and satellites — with animated EM wave propagation, interactive AM/FM modulation simulator, 3D communication chain, and 20+ real-life examples.

10Sections
20+Real-life Examples
10Diagrams
1Simulator
The Big Picture

🗺️ How Everything Connects

Before diving in, here's the entire chapter on one page. This is your mental map — every topic is a link in this chain.

Information Source Transmitter + Modulation Channel (medium) Receiver + Demod Information Output Antenna + Bandwidth Apps (satellite) EM Waves AM / FM "How do we send information from A to B without wires?" EM waves are the carrier · Modulation is the trick
Key Takeaway

Communication = transfer of information from source to destination. It needs: transmitter, channel (medium), receiver. Information (audio, video, data) is superposed on an EM wave (carrier) via modulation (AM or FM). The EM wave propagates through space (ground, sky, or space wave) and is captured by an antenna, then demodulated back to the original information. This is how radio, TV, mobile, WiFi, and satellites work!

Section 01

Introduction — The Age of Communication

15.1From Telegraph to 5G

Communication is the exchange of information between two points — the source and the destination. Historically, we've used many media: smoke signals, pigeons, telegraph wires, telephone lines, radio waves, microwaves, optical fibers, and satellites.

The revolution began in the mid-19th century with the telegraph, and then radio (Marconi, 1895) made wireless communication possible. By the 20th century, AM/FM radio, television, radar, satellites, mobile phones, and the internet followed — all built on the same principle: encode information on electromagnetic waves.

Why Communication is Special

Unlike wired communication (which needs physical cables), wireless communication uses EM waves to carry information through the air/vacuum. This is possible because EM waves can travel long distances at the speed of light (3×10⁸ m/s) and can carry energy — but to carry information, we need to modify them in a controlled way (that's modulation).

Real Life Connect — Where You Use Communication Systems
  • FM/AM radio: 88–108 MHz (FM) and 530–1710 kHz (AM) — still used everywhere.
  • Television: Terrestrial TV (VHF/UHF), cable (coaxial), satellite (DTH).
  • Mobile phones: 4G/5G — microwave frequencies (700 MHz – 40 GHz).
  • WiFi: 2.4 GHz and 5 GHz bands.
  • Bluetooth: 2.4 GHz — short-range.
  • GPS: L1 = 1575.42 MHz, L2 = 1227.6 MHz — satellite navigation.
  • Satellite TV: C-band (4-8 GHz) and Ku-band (12-18 GHz).
  • Fiber-optic internet: Light (200 THz) — not EM wave in air, but still EM wave.
  • Radio astronomy: Detects cosmic signals in 1 MHz – 1 THz range.
Key Takeaway

Communication = exchange of information. Modern world runs on EM wave–based communication. From Marconi (radio, 1895) to 5G and beyond.

Section 02

Elements of a Communication System

15.2Three Essential Blocks

Basic Components
  1. Transmitter: Converts information (audio, video, data) into a signal suitable for transmission over the medium. Usually involves modulation (superimposing the information on a high-frequency carrier).
  2. Channel (medium): Physical medium that carries the signal from transmitter to receiver. Examples: air, vacuum (for satellites), coaxial cable, optical fiber.
  3. Receiver: Extracts the original information from the received signal (demodulation). Then amplifies and reproduces the information.

An antenna is used at both ends: transmitting antenna (converts electrical signal to EM wave) and receiving antenna (converts EM wave back to electrical signal).

V1 · Block diagram of a communication system TRANSMITTER Modulation Amplification Audio Tx antenna EM waves (channel) (air / vacuum / cable) Rx antenna RECEIVER Demodulation Amplification Sound Information source → Transmitter → Channel → Receiver → Information destination
Information Sources

Types of information:

  • Voice / audio (20 Hz – 20 kHz)
  • Music / high-fidelity audio (up to 20 kHz)
  • Video / TV (0 – 4.2 MHz)
  • Digital data (bits, up to 100 Gbps in fiber)

Transducer: A device that converts one form of energy to another. For communication:

  • Microphone (sound → electrical signal)
  • Camera sensor (light → electrical signal)
  • Speaker (electrical → sound)
  • Display (electrical → light)
Real Life Connect
  • Your phone: Microphone (input) → ADC → modulator → RF amplifier → antenna (transmitter). Then receiver antenna → RF amplifier → demodulator → DAC → speaker (receiver). All in a chip!
  • WiFi router: Digitizes data → modulates on 2.4 GHz → antenna. Receives → demodulates → decodes → delivers to device.
  • Satellite TV: Broadcaster → uplink antenna (14 GHz) → satellite transponder → downlink (12 GHz) → home dish → receiver → TV.
  • Fiber internet: Router → optical transmitter (laser/LED) → fiber → photodetector → router. Modulation here is light intensity.
Key Takeaway

Communication system = transmitter + channel + receiver. Each block uses different physics: modulation (superimpose signal), propagation (EM wave travels), demodulation (extract signal). The channel determines signal loss, bandwidth, and reliability.

Section 03

Bandwidth of Signals and Transmission Media

15.3How Much Information Can a Signal Carry?

Bandwidth is the range of frequencies a signal or channel can handle. Wider bandwidth = more information per second.

Bandwidth of Common Signals
Signal TypeFrequency RangeBandwidth
Human speech (telephone quality)300 Hz – 3.1 kHz~2.8 kHz
Music (high-fidelity audio)20 Hz – 20 kHz~20 kHz
AM radio530 – 1710 kHz~10 kHz per station
FM radio88 – 108 MHz~200 kHz per station
Analog TV (one channel)54 – 890 MHz6 MHz (US) / 7 MHz (India)
Digital data (WiFi 2.4 GHz)2.4 GHz band~20-80 MHz
Optical fiber~200 THzup to THz
Bandwidth of Transmission Media
MediumTypical BandwidthNotes
Twisted pair (telephone)~1 MHzCheap, short distance
Coaxial cable~100 MHz – 1 GHzCable TV, broadband
Optical fiber~10¹⁴ Hz (bandwidth)Enormous — backbone of internet
Free space (wireless)Depends on frequency bandLimited by regulatory allocations
V2 · Signal bandwidth — audio vs video vs data Speech ~3 kHz Phone calls Music ~20 kHz FM, CD, MP3 TV Video ~4.2 MHz Analog TV Digital Data ~100 Mbps Internet, WiFi Optical Fiber ~10¹⁴ Hz ~100 Tbps Backbone of internet
Bandwidth and Channel Capacity

Nyquist theorem (for noiseless channel):

C = 2B log₂(M) bits/second

Where B = bandwidth (Hz), M = number of discrete signal levels.

Shannon-Hartley theorem (noisy channel):

C = B log₂(1 + S/N) bits/second

Where S/N = signal-to-noise ratio (linear, not dB).

These are fundamental limits — you cannot exceed them no matter how good your coding!

Real Life Connect
  • Why digital TV is better: Narrower bandwidth, better quality, no static. One analog TV channel (6 MHz) → 4 digital channels (HD).
  • 5G vs 4G: 5G uses wider bandwidth (100+ MHz) → up to 20 Gbps. 4G ~1 Gbps.
  • Why fiber is king: 100 THz bandwidth → unmatched speed. Submarine cables carry 99% of international data.
  • Bandwidth and antenna: A 100-MHz signal needs ~30 cm antenna; a 1-GHz signal needs ~3 cm; a 100-GHz signal needs ~1 mm (5G mmWave).
  • WiFi channels: 20/40/80/160 MHz channels in the 5-GHz band. Wider = faster but more interference.
Key Takeaway

Bandwidth = range of frequencies a signal/channel handles. More bandwidth = more information. Speech: 3 kHz, music: 20 kHz, video: 4.2 MHz, fiber: 10¹⁴ Hz. Nyquist and Shannon theorems give the theoretical limits.

Section 04

Propagation of EM Waves

15.4Three Ways to Reach the Receiver

Depending on the frequency and the distance, EM waves propagate by three main methods:

V3 · Three propagation modes — ground, sky, space wave GROUND WAVE (LF/MF, up to 2 MHz) Earth surface Tx Rx Wave follows Earth's curvature Used for AM radio, long-distance ship communication SKY WAVE (HF, 3–30 MHz) Ionosphere (60-400 km) Reflected by ionosphere SPACE WAVE (VHF/UHF/SHF, >30 MHz) Tx Rx Direct wave (line-of-sight) Ground-reflected wave
Three Propagation Modes

1. Ground wave (surface wave): Low frequencies (up to ~2 MHz). Wave follows the curvature of the Earth. Good for AM radio, long-range ship communication. Attenuated by Earth's surface.

2. Sky wave (ionospheric): HF (3–30 MHz). Wave reflects off the ionosphere (60–400 km altitude), allowing communication beyond the horizon — including intercontinental. Used for shortwave radio, amateur radio, some military comms. Signal quality depends on time of day and solar activity.

3. Space wave (line-of-sight): VHF/UHF/SHF (>30 MHz). Wave travels in a straight line from Tx to Rx. Both antennas must be in "line of sight." Used for FM, TV, mobile phones, WiFi, satellite, radar. Limited by Earth's curvature (typical range ~50 km for ground-based antennas).

Tropospheric scatter: A special case for UHF (0.3–3 GHz) — wave scatters off the troposphere, allowing communication over the horizon for 100+ km. Used in remote areas.

Line-of-Sight Distance

For a transmitter of height h_T and receiver of height h_R above Earth's surface, the maximum line-of-sight distance is:

d = √(2R·h_T) + √(2R·h_R)

Where R = Earth's radius = 6.37×10⁶ m.

Example: Two antennas 100 m tall → d ≈ 2 × 35.7 km = 71 km.

This is why cell towers are tall and spaced ~2-30 km apart.

Real Life Connect
  • AM radio: Ground wave reaches hundreds of km (especially at night). Sky wave bounces off ionosphere — sometimes you can hear distant AM stations at night.
  • Shortwave radio: Sky wave → intercontinental communication without satellites or cables. Used by international broadcasters (BBC World Service, VOA).
  • FM radio & TV: Space wave — must be line-of-sight. FM radio range ~50 km typical.
  • Mobile phones: Space wave — cell towers ~1-30 km apart. 5G mmWave has shorter range (~200-500 m) due to higher frequency.
  • Satellite TV: Space wave through satellite — no line-of-sight to receiver needed because satellite relays the signal.
  • Maritime VHF: Ship-to-ship and ship-to-shore VHF is space-wave — limited to ~50 km.
  • Air-ground radio: Aircraft VHF and HF communication uses sky and space wave propagation.
Common Mistake

Mistake: "All radio waves propagate by all three methods."
Correction: Different frequency ranges use different modes:

  • LF/MF (AM): ground wave
  • HF (shortwave): sky wave
  • VHF/UHF/SHF: space wave
Only some overlap is possible (e.g., HF can also use ground wave at short range).

Key Takeaway

Three propagation modes: ground wave (follows Earth, LF/MF), sky wave (bounces off ionosphere, HF), space wave (line-of-sight, VHF+). Choice depends on frequency. Cell towers need to be tall for line-of-sight.

Section 05

Need for Modulation

15.5Why We Can't Just Send the Signal Directly

You might wonder: why not just send the audio signal (20 Hz – 20 kHz) directly through an antenna? Answer: several critical reasons make direct transmission impractical.

Four Reasons We Need Modulation
  1. Antenna size: For efficient radiation, the antenna size should be comparable to λ/2 or λ/4. For a 10 kHz audio signal, λ = 30 km → antenna would need to be 7.5 km tall! Modulation with a high-frequency carrier (e.g., 1 MHz, λ = 300 m) makes antenna size manageable (~75 m).
  2. Frequency multiplexing: If all audio signals (0-20 kHz) used the same frequency band, they would interfere. Modulation shifts each signal to a different carrier frequency → many stations can coexist without interference.
  3. Wide bandwidth: A wideband signal (like audio) shifted to a high-frequency carrier can use available bandwidth efficiently.
  4. Reduced noise: Higher frequency carriers have better signal-to-noise ratio (partly), and modulation can be designed to be noise-resistant (e.g., FM > AM).
V4 · Why modulation? — the antenna size problem Without modulation (direct) antenna (m) λ (10 kHz) = 30 km Would need 7.5 km antenna! Impossible in practice With modulation antenna (m) λ (1 MHz) = 300 m Antenna ~75 m — practical! (a λ/4 dipole) Modulation shifts the signal to a high-frequency carrier → practical antenna size
What is Modulation?

Modulation: The process of superimposing the information (message) signal onto a high-frequency carrier wave.

Message signal (m(t)): The information (audio, video, data)

Carrier wave (c(t)): High-frequency sinusoid: c(t) = A_c sin(2πf_c t)

Modulated signal (s(t)): The result — carrier wave modified by the message

Three parameters of the carrier can be modulated:

  • Amplitude Modulation (AM): Vary A_c (amplitude) in proportion to m(t)
  • Frequency Modulation (FM): Vary f_c (frequency) in proportion to m(t)
  • Phase Modulation (PM): Vary φ_c (phase) — rarely used alone
Real Life Connect
  • AM radio: Audio (0-5 kHz) modulated onto carrier (530-1710 kHz).
  • FM radio: Audio (0-15 kHz) modulated onto carrier (88-108 MHz).
  • Mobile phones: Audio/video/data modulated on 700 MHz–40 GHz carriers using complex digital schemes (QAM, OFDM).
  • WiFi: Digital data on 2.4/5 GHz carriers using OFDM.
  • Digital TV: Video + audio on UHF carriers using QAM/QPSK.
  • GPS: Navigation data on L1 (1575 MHz) or L2 (1228 MHz) carriers using BPSK.
Key Takeaway

Modulation: superimpose information on high-frequency carrier. Why: (1) antenna size, (2) multiplexing, (3) bandwidth, (4) noise. AM, FM, PM are main types. It's essential for all wireless communication.

Section 06

Amplitude Modulation (AM)

15.6Varying the Amplitude

Amplitude Modulation

Message: m(t) = A_m sin(ω_m t)

Carrier: c(t) = A_c sin(ω_c t), with ω_c >> ω_m

Modulated signal:

s(t) = (A_c + A_m sin(ω_m t)) · sin(ω_c t)

The amplitude of the carrier varies between (A_c + A_m) and (A_c − A_m).

Modulation index: μ = A_m / A_c

  • μ = 0: no modulation (just carrier)
  • μ = 1: 100% modulation (maximum without distortion)
  • μ > 1: overmodulation → distortion
V5 · AM modulation — message + carrier = modulated signal Message signal m(t) — low frequency m(t) Carrier c(t) — high frequency c(t) AM signal s(t) — amplitude varies with message s(t) s(t) = (A_c + A_m sin ω_m t) · sin ω_c t  |  μ = A_m / A_c

AM Simulator — adjust modulation index

Signal Status
Good modulation
Power Distribution
P_c = 88.9%, sidebands = 11.1%
Try μ = 0 (no audio) → μ = 1 (100%, best) → μ > 1 (overmodulated, distorted)
Sidebands and Bandwidth of AM

AM signal has three frequency components:

  • Carrier: f_c (unchanged)
  • Upper sideband (USB): f_c + f_m
  • Lower sideband (LSB): f_c − f_m

The information is carried in the sidebands (carrier carries no information, just power).

AM bandwidth = 2 × f_m (twice the highest message frequency)

For audio (5 kHz max), AM bandwidth = 10 kHz.

Power in AM

Total power: P_total = P_c (1 + μ²/2)

Sideband power: P_sidebands = P_c × μ²/2

Where P_c = carrier power = A_c²/(2R).

At μ = 1 (100% modulation), sideband power = 0.5 × P_c. So 2/3 of total power is in the (useless) carrier!

This is the main disadvantage of AM — most power is wasted. This is why SSB (single-sideband) modulation exists — it strips off the carrier and one sideband.

Real Life Connect
  • AM broadcast radio: 530-1710 kHz. Stations 10 kHz apart. Audio up to 5 kHz.
  • Aircraft VHF AM: 118-137 MHz — aircraft voice comms. AM because it's simple and cheap.
  • Citizens Band (CB) radio: 27 MHz AM — truckers, hobbyists.
  • SSB (Single Sideband): Used by ham radio, maritime — more efficient than AM (only one sideband + suppressed carrier).
  • QAM (digital): Modern versions of AM — quadrature AM with digital data — used in WiFi, 4G/5G, cable modems.
Common Mistake

Mistake: "Higher modulation index = better."
Correction: Up to μ = 1 is fine (best signal-to-noise). But μ > 1 (overmodulation) causes distortion — the envelope crosses zero and information is lost. AM broadcasters keep μ around 0.3-0.7 to avoid this.

Key Takeaway

AM: vary carrier amplitude with message. μ = A_m/A_c (keep ≤ 1). Sidebands: f_c ± f_m. Bandwidth = 2f_m. Power wasted in carrier — that's why SSB exists. Simple, cheap, used in broadcast radio and aviation.

Section 07

Frequency Modulation (FM)

15.7Varying the Frequency

Frequency Modulation

Modulated signal:

s(t) = A_c sin(2πf_c t + (Δf/f_m) sin(2πf_m t))

The frequency of the carrier varies in proportion to the message signal:

f_instantaneous = f_c + k_f · m(t)

Where Δf = k_f · A_m = peak frequency deviation.

Modulation index: β = Δf / f_m

Unlike AM, FM has constant amplitude but varying frequency.

V6 · FM modulation — frequency varies with message Message signal m(t) FM signal — frequency (spacing) varies FM Amplitude constant · frequency varies Where m(t) is high → frequency higher Where m(t) is low → frequency lower s(t) = A_c sin(2πf_c t + β sin(2πf_m t))  |  β = Δf / f_m
FM vs AM
FeatureAMFM
VariesAmplitudeFrequency
AmplitudeVariesConstant
Bandwidth2f_m (e.g., 10 kHz)2(Δf + f_m) (e.g., 200 kHz)
Noise immunityPoorExcellent
RangeLong (ground + sky wave)Short (~50 km, line-of-sight)
Frequency band530-1710 kHz (MF)88-108 MHz (VHF)
Power efficiency~33% (wastes 67% in carrier)100% (constant power)
EquipmentSimple, cheapComplex, expensive
Typical useAM radio, aviationFM radio, TV audio
Why FM Has Better Noise Immunity

In AM, noise adds to the amplitude — directly corrupting the message. In FM, noise adds to amplitude but the message is in frequency changes. FM receivers use limiting circuits to strip amplitude variations, extracting only frequency → noise rejected. This is why FM sounds "cleaner" than AM.

Trade-off: FM needs much more bandwidth (200 kHz per station vs 10 kHz for AM), so it operates at higher frequencies where more bandwidth is available.

Real Life Connect
  • FM radio: 88-108 MHz. 200 kHz per station. Better sound quality, stereo, RDS data.
  • TV audio: Historically FM-modulated on a separate subcarrier.
  • Two-way radios (walkie-talkies): FM at VHF/UHF — police, fire, marine.
  • Baby monitors: FM at 49 MHz or 2.4 GHz.
  • Wireless microphones: FM modulation for clean audio.
  • FM in space: Deep Space Network uses FM for telemetry from Voyager, Mars rovers.
  • Bluetooth: Uses GFSK (Gaussian Frequency Shift Keying) — a digital FM variant.
Exam Trap

Trap: "FM has larger bandwidth because it uses higher frequency."
Correction: FM's bandwidth is larger for two reasons: (1) Wider deviation Δf, and (2) Higher message frequency range. Even at the same carrier frequency, FM bandwidth (2(Δf + f_m)) is wider than AM (2f_m). That's why FM stations must be spaced 200 kHz apart but AM stations only 10 kHz.

Key Takeaway

FM: vary carrier frequency with message. Constant amplitude. Much better noise immunity. Wider bandwidth (200 kHz per station). Used in FM radio, TV, two-way radios, Bluetooth, deep-space comms. Trade-off: needs higher frequency, more complex equipment.

Section 08

Demodulation — Getting the Message Back

15.8Extracting the Signal

Once the modulated signal reaches the receiver, we need to extract the original information. This process is called demodulation (or detection).

AM Demodulation

Envelope detector — simplest AM demodulator. Circuit: diode + RC filter.

  • Diode: Rectifies the AM signal (passes only positive halves)
  • RC filter: Averages out the high-frequency carrier, leaving the envelope (message)

Output of envelope detector = m(t) + DC offset, which is then blocked by a capacitor.

FM Demodulation

FM demodulators convert frequency variations back to amplitude (message).

Types:

  • Slope detector: Uses a tuned circuit on the slope of a resonance peak. Frequency deviation → amplitude change.
  • Foster-Seeley discriminator: Compares phases from two tuned circuits
  • Ratio detector: Improved version, less sensitive to noise
  • PLL (phase-locked loop): Modern — tracks the incoming frequency and outputs the deviation as a voltage.
V7 · AM demodulation — envelope detector AM signal in Diode + RC filter ▶| R Recovered message m(t) Envelope detector: diode rectifies → RC filter smooths → recovered audio Simple, cheap — used in every AM radio since the 1920s
Real Life Connect
  • Every AM/FM radio: Demodulator converts the received signal back to audio.
  • TV: Separate demodulators for video (AM) and audio (FM).
  • Digital TV/DAB: Demodulator + error correction + decoding.
  • WiFi: OFDM demodulator — complex digital processing.
  • Mobile phone baseband: Millions of transistors do the demodulation in software/hardware.
  • Software-defined radio (SDR): Demodulation done by software — very flexible!
Key Takeaway

Demodulation extracts the original message from the received modulated signal. AM: envelope detector (diode + RC). FM: discriminator or PLL. Essential final step in every receiver.

Section 09

Antennas

15.9Converting Signals to EM Waves (and Back)

An antenna converts an electrical signal (current/voltage) into EM waves (transmission) or vice versa (reception). It's the interface between circuits and free space.

Antenna Basics

Resonant length: For efficient radiation, antenna length ≈ λ/2 or λ/4.

Dipole antenna: Two straight conductors, length λ/2 total. Radiation pattern: donut-shaped.

Monopole antenna: Single conductor over ground plane, length λ/4.

Antenna size for common frequencies:

  • AM (1 MHz): λ/2 = 150 m — huge!
  • FM (100 MHz): λ/2 = 1.5 m — practical
  • Cell phone (2 GHz): λ/2 = 7.5 cm — tiny (chip antenna)
  • WiFi (5 GHz): λ/2 = 3 cm
V8 · Antenna size vs frequency AM (1 MHz) λ/4 = 75 m MASSIVE! FM (100 MHz) λ/4 = 75 cm Cell (2 GHz) λ/4 = 3.75 cm Chip-scale WiFi (5 GHz) λ/4 = 1.5 cm Higher frequency = smaller antenna = why mobile phones use GHz range!
Types of Antennas
  • Half-wave dipole: λ/2 length. Omnidirectional in one plane.
  • Quarter-wave monopole: λ/4, needs ground plane. Car radio antennas.
  • Yagi-Uda: Directional, 3-element (reflector + driven + directors). TV antennas.
  • Parabolic dish: Very high gain, directional. Satellite dishes, radar.
  • Horn antenna: Waveguide-based, microwave. Used in labs.
  • Patch antenna: Flat, printed. WiFi, GPS, mobile phones.
  • Phased array: Multiple elements, steerable beam. 5G, radar.
Antenna Gain

Gain G = 4πA_e/λ²

Where A_e = effective aperture area. A parabolic dish of diameter D has A_e ≈ 0.65πD²/4.

For a dish of diameter D, gain G ≈ (πD/λ)² × 0.65.

So gain ∝ (D/λ)². Larger dish or shorter wavelength → higher gain.

Effective range of communication improves with higher antenna gain on both ends.

Real Life Connect
  • Mobile phones: Internal patch antennas at 700 MHz - 5 GHz. Multiple (MIMO) for 4G/5G.
  • WiFi routers: 2-8 external antenna or internal PCB antenna.
  • Satellite dishes: Dish size 45 cm (DTH) to 30+ m (deep space). Gain ∝ (D/λ)².
  • Radio telescopes: The 500 m FAST dish in China — mind-boggling gain!
  • Cell towers: Sector antennas — 3 per tower, 120° each.
  • Air traffic control radar: Rotating parabolic dish for scanning.
  • 5G mmWave: Uses phased arrays with hundreds of tiny antennas, electronically steerable.
Key Takeaway

Antenna converts electrical signal ↔ EM wave. Size ~λ/2 or λ/4 → higher frequency = smaller antenna. Types: dipole, monopole, Yagi, parabolic, patch, phased array. Gain ∝ (D/λ)². This is why mobile phones can have tiny internal antennas (GHz frequencies).

Section 10

Satellite Communication

15.10Relaying Signals From Space

A communication satellite is a microwave repeater in orbit. It receives the uplink signal from a ground station, amplifies it, shifts frequency, and transmits the downlink signal to receivers. This enables global communication beyond the horizon.

Types of Satellites by Orbit
TypeAltitudePeriodCoverageUse
GEO (Geostationary)~35,786 km24 hoursAppears fixed over equatorTV broadcast, weather, comms
MEO (Medium Earth)~20,000 km12 hoursGlobal with 20-30 satellitesGPS, some comms
LEO (Low Earth)~500-2,000 km90-120 minNeeds constellation (tens to thousands)Starlink, Iridium, imaging
V9 · Satellite communication — uplink and downlink Earth Ground station Satellite Uplink (6 GHz) Downlink (4 GHz) Home dish Satellite relays signal — beyond line-of-sight! Uplink frequency ≠ Downlink frequency (to avoid interference)
Key Satellite Concepts

GEO satellite: Placed at 35,786 km altitude above equator. Orbits at same rate as Earth rotates → appears fixed in sky. 3 satellites can cover most of Earth. Used for TV broadcast, weather (INSAT, GOES), and comms.

Uplink/Downlink: Different frequencies (e.g., C-band: 6 GHz uplink, 4 GHz downlink). Avoids self-interference.

Footprint: The area on Earth that a satellite can "see" and serve.

Transponder: Receiver + amplifier + transmitter on satellite. A typical satellite has 12-48 transponders.

Free space path loss: Signal weakens as 1/d², so satellite needs high-gain antenna and powerful transmitters.

Real Life Connect
  • Direct-to-Home (DTH) TV: Tata Sky, Dish TV, DirecTV — GEO satellite at 36,000 km. Small dish (45-60 cm) receives signal.
  • GPS: MEO constellation of 24-32 satellites at 20,200 km altitude. Your phone receives signals from 4+ satellites to compute position to meter accuracy.
  • Starlink: LEO constellation of thousands of satellites at 550 km. Low latency (20-40 ms), broadband internet anywhere.
  • Weather satellites: INSAT-3D, GOES-16 — image clouds, track cyclones, monitor climate.
  • Military SATCOM: Encrypted global comms, navigation, early warning.
  • Deep space network: NASA's 70 m dishes communicate with Voyager 1 (24 billion km away!) — using extremely high-gain antennas and low-noise receivers.
  • Iridium, OneWeb: LEO constellations for global voice/data.
  • International Space Station: Uses Ku-band and S-band for communication.
Why 35,786 km for GEO?

From Kepler's third law, orbital period T² ∝ r³. A satellite at 35,786 km altitude (42,164 km from centre) has T = 23h 56m 4s — exactly one sidereal day. So it orbits in sync with Earth's rotation → stays fixed above one point on the equator.

Key Takeaway

Satellites relay signals beyond line-of-sight. GEO (35,786 km, fixed), MEO (GPS, 20,000 km), LEO (Starlink, 500-2,000 km). Uplink ≠ Downlink frequency. Transponders amplify. Used for TV, GPS, internet, weather. Global communication depends on satellite networks!

Practice

📝 Solved Examples

📋 2 Marks

Q1. An audio signal has bandwidth 5 kHz. Find the AM bandwidth and sideband frequencies for a 1 MHz carrier.

AM bandwidth 1 Mark

BW_AM = 2 × f_m = 2 × 5 kHz = 10 kHz

Sideband frequencies 1 Mark

Carrier: 1 MHz = 1000 kHz

USB = f_c + f_m = 1000 + 5 = 1005 kHz

LSB = f_c − f_m = 1000 − 5 = 995 kHz

BW = 10 kHz. LSB = 995 kHz, USB = 1005 kHz.
📋 3 Marks

Q2. For an AM wave with modulation index μ = 0.5, find the ratio of total power to carrier power, and sideband power to carrier power.

Formulas ½ Mark

P_total = P_c(1 + μ²/2)

P_sidebands = P_c × μ²/2

Compute 1½ Marks

P_total / P_c = 1 + (0.5)²/2 = 1 + 0.125 = 1.125

P_sidebands / P_c = (0.5)²/2 = 0.125 → sideband is 12.5% of carrier

Interpretation 1 Mark

At μ = 0.5, only 12.5% of power goes to sidebands (info). The rest (87.5%) is in the useless carrier. At μ = 1, sidebands get 50% of carrier power — a maximum. Still, 67% of total is in carrier — main AM inefficiency.

P_total/P_c = 1.125, P_sidebands/P_c = 0.125 (12.5%)
📋 3 Marks

Q3. For the AM wave s(t) = (10 + 4 sin 2π·2000t) sin 2π·10⁶t, find the modulation index, carrier frequency, and message frequency.

Identify components 1 Mark

s(t) = (A_c + A_m sin ω_m t) · sin ω_c t

A_c = 10, A_m = 4

Modulation index ½ Mark

μ = A_m/A_c = 4/10 = 0.4

Frequencies 1 Mark

Carrier: ω_c = 2π × 10⁶ → f_c = 10⁶ Hz = 1 MHz

Message: ω_m = 2π × 2000 → f_m = 2000 Hz = 2 kHz

Sidebands ½ Mark

LSB = 998 kHz, USB = 1002 kHz

μ = 0.4, f_c = 1 MHz, f_m = 2 kHz
📋 3 Marks

Q4. A TV tower has a height of 100 m. What is the maximum line-of-sight distance to a receiver antenna of the same height? (R = 6.37×10⁶ m)

Formula ½ Mark

d = √(2Rh_T) + √(2Rh_R)

Since h_T = h_R ½ Mark

d = 2√(2Rh) = 2√(2 × 6.37×10⁶ × 100)

= 2√(1.274×10⁹) = 2 × 35,700 m = 71.4 km

Interpretation 1 Mark

Even with 100 m tall towers, line-of-sight range is only ~71 km. This is why cell towers need to be spaced at most 30-50 km apart (usually less, 1-30 km, for adequate signal strength).

Effect of height ½ Mark

Doubling tower height → range increases by √2, not 2×. Range ∝ √h. So taller towers help, but with diminishing returns.

d ≈ 71.4 km
📋 3 Marks

Q5. Why is FM preferred over AM for high-fidelity music broadcasting?

Noise immunity 1 Mark

FM is inherently more immune to noise. Noise mostly affects amplitude; FM demodulator (limiter) ignores amplitude variations and extracts only frequency → rejects noise.

Wider bandwidth 1 Mark

FM uses 200 kHz per station vs 10 kHz for AM. Allows transmission of higher audio frequencies (up to 15 kHz) and stereo signals — needed for high fidelity.

Frequency band 1 Mark

FM operates at VHF (88-108 MHz) with line-of-sight — fewer stations interfere. AM (530-1710 kHz) is crowded with interference from many sources (lightning, electronics).

FM: better noise immunity, wider audio bandwidth (15 kHz vs 5 kHz), cleaner spectrum.
📋 3 Marks

Q6. A geostationary satellite is used for DTH TV. If uplink frequency is 6 GHz and downlink is 4 GHz, find the wavelengths.

Wavelengths 1 Mark

λ = c/f

Uplink: λ = 3×10⁸ / 6×10⁹ = 0.05 m = 5 cm

Downlink: λ = 3×10⁸ / 4×10⁹ = 0.075 m = 7.5 cm

Antenna sizes needed 1 Mark

λ/2 dipole: Uplink 2.5 cm, Downlink 3.75 cm

But satellite uses much larger antennas for gain!

Why different frequencies? 1 Mark

Uplink at 6 GHz, downlink at 4 GHz → 2 GHz separation. This prevents the transmitted downlink signal from interfering with the very sensitive uplink receiver. Also, lower downlink frequency experiences less atmospheric attenuation (rain fade).

Uplink λ = 5 cm, downlink λ = 7.5 cm
📋 3 Marks

Q7. Why can't we transmit audio directly without a carrier wave?

Antenna size 1 Mark

Audio at ~1 kHz has λ = 300 km → antenna would need to be 75 km tall. Impractical.

Interference 1 Mark

All audio signals use the same 0-20 kHz band — they'd all interfere. Modulation assigns each to a different carrier → separation.

Loss and noise 1 Mark

Low-frequency signals are heavily attenuated by the ground and atmosphere. High-frequency carriers propagate better via sky/space waves.

Antenna impractical, no multiplexing, poor propagation.
Quick Reference

📐 Complete Formula Sheet

Chapter 15 — All Formulas on One Page

Antenna Size
l ≈ λ/2 or λ/4
Wavelength
λ = c/f = 3×10⁸/f
AM Signal
s(t) = (A_c + A_m sin ω_m t)·sin ω_c t
Modulation Index
μ = A_m/A_c (AM) · β = Δf/f_m (FM)
AM Bandwidth
BW = 2f_m
AM Sidebands
f_c ± f_m
AM Total Power
P = P_c(1 + μ²/2)
AM Sideband Power
P_sb = P_c·μ²/2
FM Bandwidth
BW ≈ 2(Δf + f_m)
Line-of-Sight Range
d = √(2Rh_T) + √(2Rh_R)
Antenna Gain (parabolic)
G ≈ (πD/λ)² × 0.65
Nyquist Channel Capacity
C = 2B log₂(M)
Shannon Channel Capacity
C = B log₂(1 + S/N)
GEO Altitude
~35,786 km (period = 24 h)
Constants
c = 3×10⁸ m/s · R_E = 6.37×10⁶ m

📖 Notation Key

A_c, A_mCarrier, message amplitude
f_c, f_mCarrier, message frequency
ω_c, ω_mAngular frequencies (2πf)
μAM modulation index (A_m/A_c)
βFM modulation index (Δf/f_m)
ΔfFM peak frequency deviation
λWavelength
h_T, h_RTransmitter, receiver antenna height
REarth's radius
BBandwidth (Hz)
P_cCarrier power
Test Yourself

✍️ MCQ Practice

Score: 0 / 12
New Pattern

🎯 Assertion–Reason

(A) Both true, R explains A. (B) Both true, R does NOT explain A. (C) A true, R false. (D) A false, R true.

Score: 0 / 6