Home/ Physics/ Chapter 2 — Electrostatic Potential and Capacitance
Class 12 Physics · Chapter 2 · Enhanced Edition

Electrostatic Potential and Capacitance

From the water-tank analogy of potential to designing the capacitor that fires your camera flash — with deep explanations, 20+ real-life examples, 3D diagrams, an interactive simulator, exam traps and a printable formula sheet.

12Concepts
22+Real-life Examples
7Diagrams
1Simulator
The Big Picture

🗺️ How Everything Connects

Before diving into individual sections, here's the entire chapter on one page. Use this as a mental map — every topic is a link in this chain.

Potential V (Work/q) V of Point Charge Equipotential Surfaces P.E. & External Field Capacitance C = Q/V Energy & Combinations Conductors Dielectrics "E = −dV/dr — twin concepts" "Store charge + energy" Materials that shape the field
Key Takeaway

Potential (V) is the "energy landscape" of charges. It's related to field by E = −dV/dr. Once you know V, capacitance (C = Q/V) measures how much charge a conductor can store per unit potential — the foundation of every electronic circuit.

Section 01

Electrostatic Potential — The Energy Landscape

2.1–2.2What is Potential and Why Do We Need It?

Imagine hiking uphill. At every point on the hill, you have a certain gravitational potential energy — higher up = more energy. Roll a ball down and it accelerates; the "steepness" of the hill determines the force.

Electrostatic potential is exactly the same idea, but for charges instead of masses. Around any charge distribution there's an invisible "potential landscape". Positive charges naturally "roll down" from high to low potential; negative charges "roll up" (opposite direction). The steepness of this landscape at any point gives the electric field — just as the steepness of a hill gives gravitational force.

Electrostatic Potential (V)

Potential at a point = work done per unit positive charge in bringing a small positive test charge from infinity to that point (without acceleration).

V = W/q (where W = work by external force, q = test charge)

Unit: joule per coulomb (J/C) = volt (V).

Convention: Potential at infinity is taken as zero. This is like choosing the ground floor as zero height.

Analogy — Water Tanks

Think of a water tank at height h. Water at the top has higher potential energy than water at the bottom. A pipe between two tanks at different heights lets water flow from high to low. Electric potential is the "height" for charges. Positive charge flows from high V to low V (like water); negative charge flows from low V to high V (opposite).

V1 · Water tank analogy — the intuition behind potential High V₁ More energy Ground (reference) Low V₂ Less energy Water flows from high → low ΔV = V₁ − V₂ (potential difference) Charge flows from high V → low V (for positive charge)
Potential is to charges what height is to water in a tank.
Why This Matters

Potential (V) is a scalar — just a number at each point, no direction. Yet the entire vector field E can be reconstructed from it via E = −dV/dr. This is huge: instead of tracking a 3D vector field, we often just need a single scalar landscape. That's why physicists love potential — it simplifies everything.

Real Life Connect
  • Battery terminals: A 12 V car battery has a 12 J/C potential difference — each coulomb of charge gains 12 J of energy as it flows through the circuit.
  • Household sockets: 220 V AC means each coulomb carries 220 J of energy — that's why touching a live wire is so dangerous.
  • Lightning: Cloud-to-ground potential difference can be 10⁸ V — enough to ionise a kilometre of air.
  • Nerve cells: The membrane of a neuron has ~70 mV (0.07 V) potential across it — tiny but enough to trigger signals.
  • MRI machines: Use very high potentials (thousands of volts) to create the strong magnetic fields needed for imaging.
Important Convention

Only potential differences (ΔV) matter physically — the absolute value of V at a point is arbitrary because we can choose our "zero" reference anywhere. The natural choice is V = 0 at infinity (just like ground level for gravitational P.E.).

Key Takeaway

Potential V = W/q = energy per unit charge. It's a scalar "landscape" around charges. Only differences in V matter physically. Convention: V(∞) = 0. Positive charge flows high V → low V; negative flows the opposite way.

Section 02

Potential due to a Point Charge

2.3How to Calculate V from a Point Charge

Imagine bringing a tiny positive test charge from far away (infinity) to a point at distance r from a source charge Q. To get there, you must push against Q's electric field (if Q is positive) — that work gets stored as potential energy.

Potential of a Point Charge

V = (1/4πε₀) · (Q/r) = kQ/r

Where k = 9×10⁹ N·m²/C². Note:

  • V depends on sign of Q: positive for positive Q, negative for negative Q.
  • Falls off as 1/r (not 1/r² like E). Slower decay!
  • Scalar — just add numbers for multiple charges (with signs).
Real Life Connect

Compare V and E from a point charge: V ∝ 1/r falls off slowly; E ∝ 1/r² falls off fast. This is why potential remains noticeable at large distances, but field drops quickly. In practical electronics, potential (voltage) is what we measure with a voltmeter — a scalar, easier than field.

High-voltage transmission: Potential (voltage) can be 400,000 V at a power line, but the field strength at ground level is only a few hundred V/m because E falls off much faster than V.

V2 · 3D potential around a point charge — spherical shells + V = kQ/r r larger → V smaller Higher potential near charge Equipotential surfaces are concentric spheres; V decreases as 1/r V vs r r V V ∝ 1/r
3D view — potential is a set of nested spheres; graph shows 1/r decay.
Common Mistake

Mistake: "V falls off as 1/r², just like E."
Correction: No! V ∝ 1/r (slower). Only E ∝ 1/r². At very large distances, V is still noticeable while E is nearly gone. That's why potential is a more "global" quantity — it captures information at long range.

Mistake: "V is a vector."
Correction: V is a scalar. Multiple potentials just add as numbers (with signs) — no vector addition needed. This makes potentials much easier to work with than fields!

Key Takeaway

Point charge: V = kQ/r (scalar, 1/r decay). Positive Q → positive V, negative Q → negative V. Falls off slower than E. Equipotential surfaces are nested spheres.

Section 03

Potential due to an Electric Dipole

2.4Superposition at its Simplest

An electric dipole = +q and −q separated by 2a. Its potential at any point is the algebraic sum of the two charges' potentials (no vectors!). That makes dipole potential surprisingly simple:

Potential of a Dipole

At a point (r, θ) far from the dipole (r ≫ 2a):

V = (1/4πε₀) · (p cosθ / r²) where p = q·2a

Special cases:

  • On the axial line (θ = 0 or π): V = ±k·p/r²
  • On the equatorial line (θ = 90°): V = 0 (always!)
Analogy

The dipole's potential is like a "balance scale" — at the midpoint between the two charges (equatorial plane), the pull from + and − cancels exactly, giving zero potential. Move toward the + charge and it's positive; toward the − charge, negative. The value depends on the direction from the dipole's centre — this is why V depends on θ.

V3 · Dipole potential — zero on the equator, max on the axis − + Equatorial line: V = 0 everywhere V > 0 (near +) V < 0 (near −) θ=0 V = +kp/r² θ=90° V = 0 V = (1/4πε₀) · p·cosθ / r²  |  Equatorial plane: V = 0
Equipotential contours are not spherical — they're distorted by the two opposite charges.
Real Life Connect

Water molecules are dipoles with a permanent dipole moment. Each water molecule is surrounded by a dipole potential field that determines how other water molecules "line up" (hydrogen bonding). This is what gives water its extraordinarily high surface tension, high boiling point, and ability to dissolve salts.

Touchscreens with "dipole stylus": Specialized styluses are engineered as dipoles to interact with capacitive screens more predictably.

Common Mistake

Mistake: "Potential on the equatorial plane must be small but non-zero."
Correction: For an ideal dipole, V is EXACTLY zero everywhere on the equatorial plane. This is because each point is equidistant from +q and −q, so the two potentials cancel: kq/r − kq/r = 0.

Key Takeaway

Dipole potential: V = kp cosθ/r². Falls off as 1/r² (faster than point charge's 1/r). Zero everywhere on the equatorial plane. Maximum (±) on the axis.

Section 04

Potential due to a System of Charges

2.5Just Add Them Up

For multiple charges, potentials add as simple numbers (scalars), not vectors. This is what makes potential such a powerful tool:

Superposition of Potentials

Vtotal = V₁ + V₂ + V₃ + … + Vₙ = (1/4πε₀) Σ (qᵢ/rᵢ)

Where rᵢ is the distance from the i-th charge to the point. Each Vᵢ = k·qᵢ/rᵢ (with sign!).

The simplicity here is profound: to find potential at any point from any charge distribution, you just calculate k·qᵢ/rᵢ for each charge and add the numbers. No vector resolution, no components, no geometry!

V4 · Potential from many charges — just algebraic sum +q₁ −q₂ +q₃ +q₄ P V = V₁+V₂+V₃+V₄ Scalar sum! No vectors needed V = kq₁/r₁ + kq₂/r₂ + kq₃/r₃ + kq₄/r₄
Real Life Connect

Your nervous system: The potential at any point inside a nerve cell is the sum of contributions from thousands of ions (Na⁺, K⁺, Cl⁻) distributed across the membrane. This is exactly the superposition principle in action — inside your body, right now.

Molecular modeling software: Every protein folding computation starts by summing potentials from all atoms to find the electrostatic energy landscape.

Key Takeaway

Multiple charges → Vtotal = Σ Vᵢ = Σ (k·qᵢ/rᵢ). It's a SCALAR sum — no components, no angles. This is why potentials are so much easier to work with than fields. Sign of each qᵢ matters!

Section 05

Equipotential Surfaces

2.6Surfaces of Constant Potential

An equipotential surface is a surface where the potential V is the same everywhere. Move along it, and no work is done (since ΔV = 0).

Equipotential Surfaces — Key Facts
  • Point charge: concentric spheres centered on the charge.
  • Uniform field: parallel planes perpendicular to E.
  • Dipole: complicated curved surfaces (never cross).
  • Conductor in static equilibrium: the entire surface (and interior) is one equipotential.
  • Field is ALWAYS perpendicular to the equipotential surface at every point.
Why is E ⊥ Equipotential?

If E had any component along the surface, work would be done moving a charge along it (W = q·E·d). But on an equipotential, no work is done by definition. So E must have zero tangential component — i.e., E is perpendicular to the surface. This is also why field lines always cross equipotentials at 90°.

Analogy — Topographic Maps

Hikers use contour lines on maps to represent elevation. Every point on a contour line is at the same height. If you walk along a contour, you don't go up or down. The steepest uphill direction is perpendicular to the contour — same as how E-field (uphill for negative charge) is perpendicular to equipotential surfaces.

V5 · Equipotential surfaces — 4 classic cases + Point charge concentric spheres Uniform field parallel planes Dipole curved, closed surfaces Conductor V = constant Conductor entire surface + interior E is everywhere perpendicular to these surfaces Like contour lines on a hill — always ⊥ to steepest slope
Real Life Connect
  • Topographic maps: Every contour line is an equipotential of gravity. Walking along a contour = no height change = no work against gravity.
  • Conductor surfaces are equipotentials: Touching a metal object anywhere means touching the same potential — this is why birds can sit on high-voltage wires safely.
  • Faraday cages: The interior of a hollow conductor is an equipotential (same as the surface), so sensitive electronics inside are protected from external fields.
Common Mistake

Mistake: "Equipotential surfaces and field lines are parallel."
Correction: They are always perpendicular! If they were parallel, field lines wouldn't cross equipotentials — but they always do. The 90° crossing is the fundamental geometric relationship.

Key Takeaway

Equipotential surfaces have constant V. Field E is always perpendicular to them. For a point charge → spheres; uniform field → planes; conductor → the surface itself. Moving along an equipotential requires no work.

2.6.1Relation Between Field and Potential

So far we've treated V and E as separate concepts. But they're deeply linked: the field is the negative gradient of the potential:

E and V — the Fundamental Link

E = −dV/dr (in one dimension), or generally E = −∇V

Meaning: E points in the direction where V decreases fastest, with magnitude equal to the rate of decrease of V with distance.

Conversely: V = −∫E·dr (with V(∞) = 0)

Analogy

Picture a ball on a hillside. The steepness of the hill is the "field" (it tells you which way and how fast the ball will roll). The height of the hill is the "potential". A steeper hill (stronger field) means the height drops faster as you move. If the hill is flat, no force — E = 0 means V is constant. That's exactly what happens inside a conductor!

V6 · E = −dV/dr — steeper potential → stronger field Potential V(r) Distance r V Steep slope Strong E Gentle slope Weak E Field E(r) = −dV/dr Distance r E E falls faster than V (1/r² vs 1/r) E = −dV/dr: slope of V curve → value of E
Real Life Connect

Inside a conductor in equilibrium: E = 0, so dV/dr = 0 → V is constant throughout. That's why touching a metal object feels like touching the same voltage everywhere.

Between two capacitor plates: The field E is uniform, so V decreases linearly with distance — the potential "slopes down" at a constant rate from + to − plate.

Key Takeaway

E = −dV/dr. Field is the negative gradient of potential. Uniform field → V decreases linearly. Inside a conductor (E = 0) → V is constant. Steeper potential slope = stronger field.

Section 06

Potential Energy of a System of Charges

2.7Work to Assemble the Charges

If you bring two point charges q₁ and q₂ from infinity to positions r₁ and r₂, how much work does it take? That work gets stored as electrostatic potential energy:

P.E. of a Two-Charge System

U = (1/4πε₀) · q₁q₂/r₁₂ (where r₁₂ = separation)

Sign matters: U < 0 for opposite charges (attraction releases energy), U > 0 for like charges (repulsion costs energy).

For three or more charges, add up pairwise energies:

P.E. of N Charges

U = k Σi<j (qᵢqⱼ/rᵢⱼ) — sum over all distinct pairs

For 3 charges: U = k(q₁q₂/r₁₂ + q₂q₃/r₂₃ + q₁q₃/r₁₃)

V7 · Assembly of a two-charge system Step 1: bring q₁ from ∞ q₁ No field yet Work = 0 Step 2: bring q₂ from ∞ q₁ q₂ r₁₂ Work against E-field W = k·q₁q₂/r₁₂ Final energy stored U = k·q₁q₂/r₁₂ (with sign!)
Real Life Connect

Nuclear stability: In a nucleus, protons repel each other. The electrostatic P.E. is strongly positive, so if only Coulomb forces acted, nuclei would explode. It's the strong nuclear force (100× stronger, but very short range) that wins out — that's why heavy nuclei are on the edge of stability (radioactive decay).

Chemistry of atoms: Every chemical bond (ionic, covalent, metallic) is fundamentally about minimising electrostatic potential energy — electrons settle into configurations that make the total P.E. most negative.

Protein folding: The shape of every protein in your body is the one that minimises total electrostatic P.E. (plus a few other contributions). Correct folding determines function; misfolding causes diseases like Alzheimer's.

Common Mistake

Mistake: "U is always positive because it's 'energy'."
Correction: U can be positive or negative! For opposite charges, U < 0 (bound state, lower than infinite separation). For like charges, U > 0 (must push them together). This sign is essential in physics — it distinguishes stable (bound) states from unstable ones.

Key Takeaway

U12 = k·q₁q₂/r₁₂. Add pairwise for N charges. Sign matters: U < 0 means bound (stable); U > 0 means repulsion. Chemistry, biology, and nuclear physics all reduce to minimising this energy.

Section 07

Potential Energy in an External Field

2.8P.E. of a Charge in a Given Field

When a charge is placed in an external field E (created by sources far away), it has potential energy:

P.E. of a Single Charge in External Field

U = qV

Where V is the potential at the charge's location due to external sources.

For a system of two charges in an external field, you must add:

  • Energy of each charge with the external field: q₁V(r₁) + q₂V(r₂)
  • Energy of the two charges with each other: kq₁q₂/r₁₂
Total P.E. of System in External Field

U = q₁V(r₁) + q₂V(r₂) + (1/4πε₀)(q₁q₂/r₁₂)

Dipole in External Field

The most important case: a dipole in a uniform field. We saw in Chapter 1 that it experiences zero force but a torque τ = p×E. Its potential energy is:

P.E. of a Dipole in External Field

U = −pE cosθ = −p·E

θ = angle between p and E.

  • θ = 0° (aligned): U = −pE (minimum, most stable)
  • θ = 90° (perpendicular): U = 0 (reference)
  • θ = 180° (anti-aligned): U = +pE (maximum, unstable)
Real Life Connect

Microwave heating: Water molecules are dipoles. In a microwave field, they have energy U = −pE cosθ. The field oscillates 2.45 billion times/sec, forcing the dipoles to flip. Each flip is a cycle from θ = 0 → θ = 180° → back. The "friction" from this forced oscillation creates heat. That's how your food gets hot!

LCD displays: Liquid crystal molecules are dipoles. A small voltage rotates them; the resulting orientation changes which light gets through → colored pixels.

Magnetic resonance imaging (MRI): Same physics, but with magnetic dipoles (nuclei) in a magnetic field instead of electric dipoles in an electric field. The U = −μ·B energy difference between spin states gives the MRI signal.

Key Takeaway

Charge in external field: U = qV. Dipole in uniform field: U = −pE cosθ. Minimum energy when aligned (θ=0); maximum when anti-aligned (θ=180°). This energy landscape is what makes dipoles rotate and oscillate — the basis of microwave ovens and LCD screens.

Section 08

Electrostatics of Conductors

2.9Five Golden Rules

In static equilibrium (no current flowing), conductors obey five remarkable properties:

Electrostatic Properties of Conductors
  1. E = 0 everywhere inside a conductor.
  2. E is normal to the surface at every point just outside.
  3. All excess charge resides on the surface — no net charge inside.
  4. V is constant throughout the conductor (volume + surface).
  5. The field just outside is E = σ/ε₀ (σ = local surface charge density).
Why E = 0 inside?

If E were non-zero inside a conductor, free electrons would move (they're free, after all). But "static equilibrium" means no current. So E must be zero. This is such a powerful constraint that it forces all the other properties: no field inside means all charge must sit on the surface (Gauss's law), which means surface is equipotential, which means field is perpendicular to the surface.

V8 · Conductor — field zero inside, all charge on surface, Faraday cage E = 0 (cavity shielded) + + + + + + + + + + + + + + + + + + Inside conductor E = 0 (free electrons cancel it) V = constant throughout All excess charge on surface E ⊥ surface, E = σ/ε₀ just outside Cavity E = 0 even if outside field exists This is electrostatic shielding Faraday cage concept
Conductor: all charge on surface, field zero inside, cavity fully shielded.
Real Life Connect
  • Lightning rod: The field at a sharp tip is very strong (E = σ/ε₀ with high σ at tip). Ionises air, provides safe path to ground.
  • Car during thunderstorm: The metal body is a Faraday cage — safe even if struck by lightning. (Must be fully enclosed; not touching outside-connected parts.)
  • MRI rooms: Metal-shielded rooms keep strong external fields out (and internal fields in).
  • Sensitive electronics: Wrapped in conducting bags during shipping. The bag's surface charge shields the electronics.
  • Coaxial cables: The outer conductor shields the inner signal from external interference.
Electrostatic Shielding (Faraday Cage)

If a cavity inside a conductor has no charge, the field inside the cavity is zero, regardless of what happens outside. This is because any external field causes surface charges to redistribute on the conductor, exactly cancelling the field inside. This is called electrostatic shielding — a crucial concept in electronics, aerospace, and MRI technology.

Common Mistake

Mistake: "The field is zero at the surface of a conductor."
Correction: The field is zero inside, but just outside the surface, E = σ/ε₀ (can be very large). Charges reside on the surface precisely to make the interior field zero — but the surface itself has strong field right outside it.

Key Takeaway

In electrostatic equilibrium, a conductor has E = 0 inside, all charge on the surface, V constant throughout, and E normal to surface. Cavities are shielded from outside — this is the Faraday cage / electrostatic shielding principle behind MRI rooms, coaxial cables, and lightning safety.

Section 09

Dielectrics and Polarisation

2.10Insulators in an Electric Field

A dielectric is an insulator — no free charges to move. But dielectrics still respond to electric fields through a process called polarisation:

Polarisation

When a dielectric is placed in an external field E₀, its molecules form tiny dipoles (or existing dipoles align). This creates a net induced surface charge that produces a field Einduced opposing E₀.

Result: The net field inside the dielectric is reduced: E = E₀/K, where K is the dielectric constant (K > 1 for all dielectrics).

Two types of molecules

Type Description Example
Non-polar No permanent dipole (centres of + and − charge coincide). Under external field, they get "stretched" into induced dipoles. O₂, H₂, CO₂, CH₄
Polar Have permanent dipole moment even without field. Under external field, they rotate to align. H₂O, HCl, NH₃
V9 · Dielectric polarisation — molecules align to oppose E Before external field Random orientation, no net dipole After external field E₀ + + + + + − − − − − E₀ All dipoles aligned → induced surface charge
Random dipoles (left) → aligned under external field, creating opposing surface charge (right).
Dielectric Constant K

K = E₀/E = C/C₀ = ε/ε₀

Where C₀ = capacitance in vacuum, C = capacitance with dielectric. K is dimensionless. For vacuum, K = 1. For air, K ≈ 1.0006 (basically 1). For glass, K ≈ 5–10. For water, K ≈ 80 (very high!). For BaTiO₃ (ceramic), K can be ~1000+.

Real Life Connect
  • Water's K ≈ 80 — highest among common liquids. This is why water is such a great solvent: it "insulates" ions from each other so strongly that they float free instead of pairing up.
  • Ceramic capacitors use BaTiO₃ or other high-K materials, achieving huge capacitance in tiny packages — like the ones in your phone charger.
  • Air is essentially vacuum (K = 1) — practical capacitors use solid dielectrics (mica, ceramic, polyester film) to boost capacitance dramatically.
  • Glass/mica (K = 5–10) are used in high-voltage capacitors where stable behaviour is needed.
Key Takeaway

Dielectric polarisation reduces internal field: E = E₀/K. K = ε/ε₀ is dimensionless, ≥1. Polar molecules align; non-polar get stretched. High-K dielectrics (water, ceramics) enable compact capacitors and stabilize ions in solution.

Section 10

Capacitors and Capacitance

2.11–2.12Storing Charge — the "Battery of the Moment"

A capacitor is a pair of conductors separated by an insulator. When you connect it to a battery, one plate gets +Q and the other gets −Q. Its capacitance measures how much charge it can hold per unit voltage:

Capacitance

C = Q / V

Unit: farad (F) = coulomb per volt = C/V. Practical: 1 μF = 10⁻⁶ F, 1 pF = 10⁻¹² F.

Note: C depends only on geometry and dielectric — NOT on Q or V. Double Q → double V; the ratio stays the same.

Parallel Plate Capacitor

The simplest capacitor: two metal plates of area A, separated by distance d.

Parallel Plate Capacitance

Vacuum: C₀ = ε₀A / d

With dielectric: C = Kε₀A / d = εA / d

Where ε = Kε₀ = permittivity of the dielectric medium.

V10 · 3D parallel plate capacitor — field uniform between plates + + + + + + + + + + + + + + + + (Top plate, +Q) − − − − − − − − − − − − − − − − (Bottom plate, −Q) E = σ/ε₀ = V/d d Plate area A, separation d → C = ε₀A/d E is uniform between plates (neglecting edge effects)
Uniform field E between the plates — the fundamental capacitor model.
Real Life Connect
  • Camera flash: A capacitor (~100–300 μF at 300 V) charges slowly from the battery, then dumps ~50 J into the flash tube in ~1 ms. That's why there's a "whine" then a sudden bright flash.
  • Defibrillator: Stores ~200–360 J of energy in a large capacitor. When discharged through the patient's chest in ~10 ms, it delivers a shock that resets the heart's rhythm. Same physics — faster, bigger.
  • Touchscreens: Your finger changes the local capacitance of the screen when it touches. The controller chip detects this tiny change and registers a "tap".
  • Electrolytic capacitors in power supplies smooth out the "ripples" from AC-to-DC conversion. They're the little cylinders on every circuit board.
  • Supercapacitors in electric buses and regenerative braking systems: 3000 F at 2.7 V — enormous capacitance for energy storage.
  • Tuning circuits in old radios: variable capacitor adjusts resonant frequency to pick a station.
  • DRAM in computers: each bit is a tiny capacitor (~10 fF) — charged = 1, discharged = 0.
Common Mistake

Mistake: "Capacitance depends on Q or V."
Correction: C = Q/V is a definition of C, but C itself is determined only by geometry and dielectric. Double Q → double V, so C stays the same. This is like resistance — R = V/I, but R depends only on the wire's material and dimensions.

Mistake: "A capacitor stores charge."
Correction: Strictly, the total charge on a capacitor is zero (equal +Q and −Q). What it stores is energy and charge separation. The "charge Q on a capacitor" means the magnitude of charge on either plate.

Key Takeaway

C = Q/V, unit farad. Parallel plate: C = ε₀A/d (or εA/d with dielectric). Depends only on geometry and dielectric — not on Q or V. Camera flashes, defibrillators, supercapacitors, DRAM — all rely on this simple relation.

2.13Effect of Dielectric on Capacitance

Inserting a dielectric between plates increases capacitance by factor K:

With Dielectric

C = K·C₀ = Kε₀A/d (K > 1, so C increases)

But the behaviour depends on what's held constant:

  • Voltage constant (battery connected): Q increases, V stays same, C increases by K. Stored energy U = ½CV² increases.
  • Charge constant (battery disconnected): V decreases (V = V₀/K), Q stays same, C increases by K. Stored energy U = Q²/2C decreases (dielectric pulls itself in!).
Why does a dielectric get pulled into a capacitor?

When the plates are charged and disconnected, inserting a dielectric reduces the energy (U = Q²/2C with C increased). Nature minimises energy, so the dielectric gets sucked in by the field. This is the same principle behind how liquid crystal displays respond to voltage — the liquid crystal's polarisation causes it to move/rotate.

Real Life Connect

Electrolytic capacitors use an extremely thin oxide layer (high K, tiny d) as dielectric — this gives huge capacitance in a small package. But polarity must be respected: connect backwards and the oxide layer breaks down, causing explosion.

Ceramic capacitors use BaTiO₃ (K up to 10,000) for MLCCs (multilayer ceramic capacitors) — the tiny chip capacitors in your phone, thousands of them per device.

Key Takeaway

Dielectric multiplies capacitance by K. If battery stays connected, Q increases and V fixed. If disconnected, Q fixed and V decreases. Energy change depends on which case — a classic tricky board question.

Section 11

Combination of Capacitors

2.14Series and Parallel

Potential & Field Simulator — see how V and E fall off differently

Potential V = kQ/r
1.80×10⁵ V
Field E = kQ/r²
1.80×10⁶ N/C

Series Combination

Capacitors connected end-to-end. Same charge Q on each (inner plates connected only to each other); total voltage = sum of voltages.

Series Combination

1/Ceq = 1/C₁ + 1/C₂ + 1/C₃ + …

Ceq is ALWAYS smaller than the smallest individual capacitor. Opposite of resistors!

Parallel Combination

All positive plates connected together, all negative together. Same voltage across each; total charge = sum of charges.

Parallel Combination

Ceq = C₁ + C₂ + C₃ + …

Ceq is ALWAYS larger than the largest individual capacitor.

V11 · Series vs parallel — schematic comparison SERIES: 1/C = 1/C₁ + 1/C₂ C₁ C₂ C₃ V +Q −Q −Q +Q Same Q, voltages add PARALLEL: C = C₁ + C₂ + C₃ C₁ C₂ C₃ V Same V, charges add
Real Life Connect
  • Smartphone battery: Internally has many small capacitor cells in parallel to increase total capacitance / energy storage.
  • High-voltage capacitor banks: Series-connected to share the high voltage (each sees only a fraction).
  • Supercapacitor banks: Series for high voltage, parallel for high capacitance — engineers tune for the application.
  • Photography strobes: Multiple capacitors in parallel to dump more energy faster.
Exam Trap

Critical distinction: Capacitors in series: Ceq < smallest. Capacitors in parallel: Ceq > largest. This is OPPOSITE to how resistors behave. The reason: for capacitors, parallel plates share the voltage (like water in parallel pipes), while series plates share charge.

Another trap: When you add capacitors, voltage does NOT add in parallel, charge does NOT add in series. Each has its own conservation rule. Always check the physical connections carefully.

Key Takeaway

Series: 1/Ceq = Σ 1/Cᵢ (smaller than smallest). Parallel: Ceq = Σ Cᵢ (larger than largest). This is opposite to resistors! Both combos are used in real circuits to tune voltage and capacitance.

Section 12

Energy Stored in a Capacitor

2.15Charging Stores Energy — Where Does It Go?

When you charge a capacitor, you do work against the electric field. That work gets stored as electrostatic potential energy — ready to be released when needed.

Energy Stored in a Capacitor

U = ½ CV² = ½ QV = Q²/(2C)

All three are equivalent (using C = Q/V). Choose whichever is easiest for your problem.

Energy Density

The energy is stored in the electric field between the plates. Energy per unit volume (energy density) is:

Energy Density

u = ½ ε₀ E² (in vacuum)  |  u = ½ ε E² (in dielectric)

This result is universal — it applies to ANY electric field, not just capacitor plates!

V12 · Charging a capacitor — energy builds up Energy = area under V-Q graph Charge Q Voltage V Area = ½ QV = Energy stored (Q, V) Energy Formulas U = ½ CV² (easy when V is known) U = ½ QV (easy when Q and V both known) U = Q²/(2C) (easy when Q is fixed / disconnected) Charging = gradual buildup of energy
Real Life Connect
  • Camera flash: ~50 J stored in a capacitor at 300 V. Discharged in ~1 ms — power delivery rate is ~50 kW, far more than any battery could supply that fast.
  • Defibrillator: ~200–360 J of energy. The capacitor charges for seconds, then delivers it all in ~10 ms through the chest.
  • Railgun / electromagnetic launch: Massive capacitor banks discharge in microseconds to accelerate projectiles — hundreds of MJ of energy from a bank of capacitors.
  • Regenerative braking: Supercapacitors capture the energy from slowing down a bus/train (instead of losing it as heat).
  • Pacemakers: Small capacitor discharges ~10 μJ into the heart at each beat — tiny but precise energy dose.
Why is U = ½ CV² not CV²?

Because you don't charge the capacitor instantly! When the capacitor has charge q (between 0 and Q), the voltage is v = q/C. To add dq more charge, you do work dW = v·dq = (q/C)dq. Integrating from q=0 to q=Q: W = ∫(q/C)dq = Q²/2C = ½CV².

The factor ½ comes from the "average" voltage during charging — starts at 0, ends at V, so average = V/2. Work = Q × (V/2) = ½QV.

Common Mistake

Mistake: "U = QV (forgetting the ½)."
Correction: Always include ½. The ½ appears because charging is a gradual process — voltage isn't constant throughout.

Mistake: "When you connect two capacitors, energy is conserved."
Correct fact: When you connect charged capacitor to uncharged one, the final energy is LESS than initial — some energy is lost as heat/EM radiation in the connecting wires. This is a classic "where did the energy go?" problem. (The answer: heat/radiation.)

Key Takeaway

Energy in a capacitor: U = ½CV² = ½QV = Q²/2C. Stored in the field with density u = ½ε₀E². The ½ is essential — don't drop it. Camera flashes, defibrillators, regenerative braking, railguns — all rely on rapid energy release from capacitors.

Practice

📝 Solved Examples with Step Marking

📋 2 Marks

Q1. A point charge Q = 5 μC is at distance 30 cm from a point P. Find the electric potential at P.

Given ½ Mark

Q = 5×10⁻⁶ C, r = 0.3 m

Formula ½ Mark

V = kQ/r

Compute 1 Mark

V = (9×10⁹ × 5×10⁻⁶)/0.3 = 4.5×10⁴/0.3 = 1.5 × 10⁵ V

V = 1.5 × 10⁵ V
📋 3 Marks

Q2. Two charges +2 μC and −2 μC are placed 4 cm apart. Find the potential at the midpoint between them.

Setup ½ Mark

Each charge is 2 cm = 0.02 m from midpoint.

Potential from each 1½ Marks

V₁ = k(2×10⁻⁶)/0.02 = 9×10⁵ V
V₂ = k(−2×10⁻⁶)/0.02 = −9×10⁵ V

Sum 1 Mark

V = V₁ + V₂ = 0 V

This makes sense — midpoint is on the equatorial plane where V = 0 for a dipole.

V = 0 V
📋 3 Marks

Q3. A parallel plate capacitor has plates of area 0.02 m² separated by 1 mm of air. Calculate its capacitance.

Given ½ Mark

A = 0.02 m², d = 10⁻³ m, ε₀ = 8.85×10⁻¹² C²/N·m²

Formula ½ Mark

C = ε₀A/d

Compute 1½ Marks

C = (8.85×10⁻¹² × 0.02)/10⁻³
= 1.77×10⁻¹³/10⁻³
= 1.77 × 10⁻¹⁰ F = 177 pF

Check units ½ Mark

Farad = C/V ✓

C = 177 pF
📋 3 Marks

Q4. Three capacitors C₁ = 2 μF, C₂ = 3 μF, C₃ = 6 μF are connected in series. Find the equivalent capacitance.

Formula ½ Mark

1/Ceq = 1/C₁ + 1/C₂ + 1/C₃

Substitute 1½ Marks

1/Ceq = 1/2 + 1/3 + 1/6 = 3/6 + 2/6 + 1/6 = 6/6 = 1

Result ½ Mark

Ceq = 1 μF

Sanity check ½ Mark

1 μF is smaller than smallest (2 μF) ✓

Ceq = 1 μF
📋 5 Marks

Q5. A 100 pF capacitor is charged to 100 V. Find (a) charge, (b) energy stored.

Given ½ Mark

C = 100×10⁻¹² F, V = 100 V

(a) Charge 1½ Marks

Q = CV = 100×10⁻¹² × 100 = 10⁻⁸ C = 10 nC

(b) Energy — formula 1 1 Mark

U = ½ CV²

Compute 1½ Marks

U = ½ × 100×10⁻¹² × (100)²
= ½ × 100×10⁻¹² × 10⁴
= 5 × 10⁻⁷ J

Alternative check ½ Mark

U = ½QV = ½ × 10⁻⁸ × 100 = 5 × 10⁻⁷ J ✓

Q = 10 nC, U = 5 × 10⁻⁷ J
📋 5 Marks

Q6. A capacitor of 10 μF is charged to 100 V. It is then disconnected and connected to an identical uncharged capacitor. Find (a) common potential, (b) energy lost.

Initial state ½ Mark

Q = CV = 10×10⁻⁶ × 100 = 10⁻³ C. Energy U₁ = ½CV² = 5×10⁻² J.

(a) Common potential 1½ Marks

Total Q conserved = 10⁻³ C. Total C = 10+10 = 20 μF.
V' = Q/Ctotal = 10⁻³/(20×10⁻⁶) = 50 V

(b) Final energy 1 Mark

U₂ = ½ × Ctotal × V'² = ½ × 20×10⁻⁶ × 2500 = 2.5×10⁻² J

Energy lost 1 Mark

ΔU = U₁ − U₂ = 5×10⁻² − 2.5×10⁻² = 2.5 × 10⁻² J

Where did it go? 1 Mark

Lost as heat in the connecting wires and electromagnetic radiation. This is a classic "paradox" — energy is NOT conserved in this process (unless you account for the radiation).

V' = 50 V, energy lost = 2.5 × 10⁻² J
📋 3 Marks

Q7. Why is the electric field inside a hollow conductor zero in electrostatic equilibrium?

Reasoning 1½ Marks

If E ≠ 0 inside, free electrons would move. That would be a current — contradicts "static equilibrium".

Gauss's law argument 1½ Marks

Draw a Gaussian surface inside the conductor. Since no charge can be inside (all excess charge on surface), qenc = 0. So ∮E·dS = 0. By symmetry, E = 0 inside.

E = 0 inside — free charges cancel any internal field
Quick Reference

📐 Complete Formula Sheet

Chapter 2 — All Formulas on One Page

Potential Definition
V = W/q
Point Charge Potential
V = kQ/r
Dipole Potential
V = k·p·cosθ/r²
Superposition (Potentials)
V = Σ Vᵢ = Σ k·qᵢ/rᵢ
E from V
E = −dV/dr
Two-Charge P.E.
U = k·q₁q₂/r₁₂
P.E. in External Field
U = qV
Dipole in External Field
U = −pE cosθ
Conductor Field Outside
E = σ/ε₀ (normal to surface)
Dielectric Effect
E = E₀/K
Dielectric Constant
K = ε/ε₀ = C/C₀
Capacitance Definition
C = Q/V
Parallel Plate (Vacuum)
C₀ = ε₀A/d
Parallel Plate (Dielectric)
C = Kε₀A/d = εA/d
Series Combination
1/Ceq = 1/C₁ + 1/C₂ + …
Parallel Combination
Ceq = C₁ + C₂ + …
Energy Stored
U = ½CV² = ½QV = Q²/2C
Energy Density
u = ½ε₀E²
Constants
k = 9×10⁹, ε₀ = 8.854×10⁻¹², e = 1.6×10⁻¹⁹

📖 Notation Key

V Electric potential (volt, V) — scalar
E Electric field (N/C or V/m) — vector
U Potential energy (joule, J)
W Work done (joule, J)
C Capacitance (farad, F)
Q Charge on one plate (coulomb, C)
K Dielectric constant (dimensionless)
ε₀ Permittivity of free space = 8.854×10⁻¹²
ε Permittivity of dielectric = Kε₀
σ Surface charge density (C/m²)
A Plate area (m²)
d Plate separation (m)
u Energy density (J/m³)
Test Yourself

✍️ MCQ Practice

Score: 0 / 12
New Pattern

🎯 Assertion–Reason

(A) Both true, R explains A. (B) Both true, R does NOT explain A. (C) A true, R false. (D) A false, R true.

Score: 0 / 6