Home/ Physics/ Chapter 3 — Current Electricity
Class 12 Physics · Chapter 3 · Enhanced Edition

Current Electricity

From the lightning in the sky to the electrons inside your phone battery — with deep explanations, 20+ real-life examples, 3D diagrams, an interactive Ohm's law simulator, exam traps and a printable formula sheet.

12Concepts
22+Real-life Examples
10Diagrams
1Simulator
The Big Picture

🗺️ How Everything Connects

Before diving into individual sections, here's the entire chapter on one page. Use this as a mental map — every topic is a link in this chain.

Current I = q/t Ohm's Law V = IR Drift & Resistivity Power & Heating EMF & Cells Kirchhoff + Bridge Conductors Temperature "Free electrons + collisions" "Source of voltage" Materials that shape the flow
Key Takeaway

Current flows when free electrons are pushed by a field. Ohm's law relates V, I, R. R depends on material (ρ) and geometry. Power is dissipated as heat. Real circuits need EMF (batteries) and multiple components — solved by Kirchhoff's rules and the Wheatstone bridge.

Section 01

Electric Current — The Flow of Charge

3.1–3.2What is Current and Why Does It Flow?

Imagine water flowing through a pipe. Charge flowing through a wire is exactly the same idea — but the "water" is free electrons in a metal (or ions in a liquid). The current is the rate at which charge flows past a point:

Electric Current

I = Q / t (average), or I = dQ/dt (instantaneous)

Unit: ampere (A) = coulomb per second (C/s).

Conventional direction: direction of positive charge flow. In metal wires, actual electrons flow in the opposite direction. This is a historical convention (Franklin's choice) that we still follow.

Analogy — Water in Pipes

Think of a wire as a pipe. The electrons are water molecules. The battery is a pump that maintains pressure. The voltage (potential difference) is the water pressure. Current is the volume of water flowing per second. Higher pressure → more current. Resistance is "pipe narrowness" — narrow pipes resist flow.

V1 · Water-pipe analogy — current is like water flow High V (battery +) Current I (like water flow) Low V (battery −) Battery = pump − + Drives current Higher V → more current I. Narrower pipe (higher R) → less I.
Electric current is the flow of charge driven by potential difference — just like water in a pipe.
Real Life Connect
  • USB charger: 1 A current means ~6.25×10¹⁸ electrons flowing per second through your charging cable.
  • LED bulb: ~0.05 A (50 mA) — tiny current, but because it's efficient, it produces lots of light.
  • Lightning: A single strike carries ~30,000 A for ~30 microseconds — that's 1 coulomb of charge in a flash.
  • Household wiring: A 15 A fuse protects a circuit designed for ~2000 W (with 220 V supply).
  • Nerve signals: Current inside a neuron is ~picoamperes (10⁻¹² A) — thousands of times smaller than an LED!
  • Superconductor magnet in MRI: Currents of ~2000 A flowing in a loop with zero resistance — no energy lost forever.
Why "Conventional Current" Direction?

Franklin guessed (incorrectly) that positive charge flows in the direction of current. It turns out electrons (which are negative) flow the opposite way. But we still use the conventional direction for all circuit analysis — it works equally well. Just remember: when you say "current flows from + to −", the actual electrons flow from − to +.

Common Mistake

Mistake: "Electrons move at the speed of light through a wire."
Correction: Electrons actually drift at a snail's pace — typically ~0.1 mm/s (see the drift velocity section). BUT the electromagnetic field signal propagates at nearly c, so a bulb lights up almost instantly when you flip the switch.

Mistake: "Current gets used up in a circuit."
Correction: Current is conserved — the same amount of charge flows per second at every point in a series circuit. What gets used up is energy, not current.

Key Takeaway

Current I = dQ/dt. Conventionally flows + → −. Actual electrons flow − → +. Unit: 1 A = 1 C/s. Current is conserved (same throughout series circuit). Only energy is used up.

Section 02

Electric Currents in Conductors

3.3Free Electrons — The "Sea of Charge"

In a solid metal, atoms are packed together, and some of the outermost electrons are not bound to any specific atom. They form a "sea" of free electrons moving randomly through the metal, bouncing off the fixed positive ions.

These "free" electrons move randomly at very high thermal speeds (~10⁶ m/s), but in all directions — so the net current is zero. But apply a voltage (electric field) across the conductor, and the electrons get a small drift velocity superimposed on their random motion — that's the current!

Current in a Wire — the Microscopic Picture

If the wire has cross-section area A, and n is the number of free electrons per unit volume (carrier density), and v_d is the drift speed, then:

I = n·e·A·vd

Where e = 1.6×10⁻¹⁹ C (electron charge).

V2 · Live electron flow — actual electrons move one way, conventional current the other − + − − − − − − − Conventional current I → ← Actual electron flow Yellow dots = fixed positive ions · Blue dots = free drifting electrons Current I = n·e·A·v_d
Electrons drift opposite to conventional current direction — same physical situation, two sign conventions.
Real Life Connect
  • Copper wire (typical home): n ≈ 8.5×10²⁸ electrons/m³, A ≈ 10⁻⁶ m². At 1 A, v_d ≈ 0.07 mm/s!
  • Electrolytic solutions: both positive ions (Na⁺, H⁺) and negative ions (Cl⁻) move — both contribute to current.
  • Semiconductors: electrons + "holes" (missing electrons) both carry current. These are the basis of all transistors.
  • Vacuum tubes: old TVs and X-ray tubes use electrons flowing through vacuum — no atoms to slow them down, but limited by space charge.
  • Plasma (neon signs): both electrons and positive ions move freely — that's why neon tubes glow.
Key Takeaway

Current in a conductor = flow of free electrons. I = n·e·A·v_d. Electron drift is slow (~0.1 mm/s) but the "signal" propagates at ~c. In metals, only electrons move; in solutions, both + and − ions can move.

Section 03

Ohm's Law

3.4The Simplest Relationship in Electronics

George Ohm (1828) discovered that, for many conductors, current is proportional to voltage:

Ohm's Law

V = I · R (or I = V/R)

Where R is the resistance (unit: ohm, Ω).

Alternatively, at the microscopic level: j = σE (current density = conductivity × field). Both forms are equivalent.

What is Resistance?

Resistance is the opposition to current flow. For a wire of length ℓ and cross-section A:

Resistance of a Wire

R = ρ·ℓ / A

Where ρ is the resistivity — a material property (unit: Ω·m). Longer wire → more R. Thicker wire → less R.

Conductivity σ = 1/ρ.

Ohm's Law Simulator — drag the sliders to see current and power change

Current I = V/R
1.20 A
Power P = VI
14.4 W
Heat = I²R
14.4 W
V3 · V-I graph — Ohmic vs non-Ohmic devices Ohmic resistor Current I (A) Voltage V slope = R (constant) Straight line through origin Diode (non-Ohmic) Voltage V Current I Not a straight line Curve → non-Ohmic
Ohmic conductors give linear V-I (constant R). Diodes and other non-Ohmic devices give curves.
Real Life Connect
  • House wiring (copper): Follows Ohm's law very well. That's why we can predict currents and use fuses.
  • Light bulb filament (tungsten): Nearly Ohmic at low current, but resistance increases with temperature (glows white-hot). Slightly non-Ohmic in practice.
  • Resistors in electronics: Carbon or metal film resistors — carefully designed to be Ohmic. The breadboard staple.
  • LED / diode: NOT Ohmic — behaves like a one-way valve with a threshold voltage (2 V for red LEDs). Very nonlinear.
  • Thermistors: Deliberately non-Ohmic — resistance changes with temperature. Used as temperature sensors.
  • LDR (light-dependent resistor): Resistance drops dramatically in light. Used in automatic street lights.
Common Mistake

Mistake: "V = IR is Ohm's law."
Correction: V = IR is a definition of resistance — it works for ANY device. Ohm's law is the additional claim that R is constant (independent of V and I). The "law" is the constancy of R, not the equation.

Mistake: "Ohm's law is universal."
Correction: It's an empirical observation, not fundamental. Many devices (diodes, LEDs, thermistors) don't follow it. It's approximate even for metals at very high currents (heating changes R).

Key Takeaway

Ohm's law: V = IR (with R constant). R = ρ·ℓ/A. Microscopic form: j = σE. It's an empirical observation, not universal — diodes, LEDs, thermistors don't follow it.

Section 04

Drift of Electrons & Origin of Resistivity

3.5The Microscopic Theory of Conduction

Let's zoom into a wire. Free electrons are moving at ~10⁶ m/s randomly (thermal speed), colliding with the fixed positive ions. On average, they don't move anywhere — random directions cancel.

Now apply a voltage (electric field E). Electrons accelerate in the direction opposite to E. But they don't keep accelerating forever — each collision "resets" their velocity, and they end up moving with a slow average drift velocity:

Drift Velocity

vd = e·E·τ / m (where τ = average time between collisions, called relaxation time)

Typical values: v_d ~ 0.1 mm/s (yes, really!). Even though individual electrons move at 10⁶ m/s, the net drift is super slow.

Also, in terms of voltage V across length L: vd = e·V·τ / (m·L)

Resistivity from Microscopic Picture

ρ = m / (n·e²·τ)

Where m = electron mass, n = carrier density, e = electron charge, τ = relaxation time.

Higher ρ means lower τ (frequent collisions) or lower n (fewer carriers).

Mobility

μ = vd/E = e·τ/m (unit: m²/V·s)

Mobility measures how "responsive" a carrier is to a field. Higher μ → faster drift → higher conductivity.

V4 · Drift with collisions — zigzag path through wire E field pushes electrons − Net drift velocity v_d ≈ 0.1 mm/s (opposite to E) collision collision collision collision
Electrons zigzag randomly but drift slowly opposite to the field — like a ball in a pinball machine tilted slightly.
Analogy — Marbles in a Tube

Imagine marbles rolling down a slightly tilted tube full of pegs. Each marble bounces randomly off pegs (like electrons off atoms), but on average it slowly moves downhill. The tilt of the tube is the electric field. The "average downhill speed" is the drift velocity — much slower than the marble's instantaneous speed.

Real Life Connect
  • Why copper is the best everyday conductor: high n (one free electron per atom), high τ (few collisions with impurities). ρ ≈ 1.7×10⁻⁸ Ω·m — lowest among common metals.
  • Why nichrome is used in heaters: much higher ρ (×60 that of copper) — it gets hot fast and dissipates lots of power.
  • Why wires are thick for high current: bigger A means more parallel paths for electrons — smaller R and less heating.
  • Why the bulb lights instantly even though electrons are slow: the field propagates at nearly c, pushing all electrons throughout the wire to start drifting almost simultaneously.
  • Electromigration in ICs: at very high current densities, electron drift "pushes" metal atoms out of place — this is a major failure mode in microchips.
Why Do Electrons Not Accelerate Forever?

Because they collide with the lattice ions. Each collision randomises their direction, so they lose the "drift" they've just built up. Between collisions they accelerate; after collision they're back to random. The result is a steady average drift velocity — like a ball reaching terminal velocity in a viscous fluid.

This is also why resistance exists at all — without collisions, current would flow forever in a superconductor (zero resistance).

Common Mistake

Mistake: "Drift velocity increases with time as current flows."
Correction: Drift velocity reaches a steady value almost instantaneously (~10⁻¹⁴ s). It depends on E (or V) and τ, not on time.

Mistake: "Drift velocity is the same as electron speed."
Correction: Drift velocity (~0.1 mm/s) is the average net velocity. Individual electron thermal speeds are ~10⁶ m/s — 10¹⁰ times faster, but in random directions!

Key Takeaway

v_d = eEτ/m = eVτ/(mL) — very slow. ρ = m/(ne²τ). Mobility μ = eτ/m. Collisions with ions cause resistance. Copper is excellent because it has high n and τ. Temperature affects τ → affects ρ.

Section 05

Limitations of Ohm's Law

3.6When V = IR Doesn't Hold

Ohm's law works beautifully for metals at constant temperature. But many devices break the rules — and that's where the interesting electronics lives!

Type of deviationDescriptionExample
Non-linearV vs I is not a straight line. R changes with V or I.Diode, LED, varistor
Sign-dependentCurrent for +V is different from current for −V (same magnitude).Diode — conducts only one way
Non-uniqueMore than one V for the same I (hysteresis).GaAs, memristors
Temperature-dependentR changes significantly with T.Tungsten filament, thermistors
Real Life Connect
  • LEDs: They only conduct when forward-biased above ~2 V. Below that, no current. Above, current rises exponentially. That's why LEDs need current-limiting resistors.
  • Thermistors: Resistance changes dramatically with temperature. Used in thermostats, car engines, and phone batteries to monitor temperature.
  • LDRs: Resistance drops from megohms in dark to a few hundred ohms in bright light. Basis of automatic lighting systems.
  • Varistors (MOVs): Protect electronics from voltage spikes. At normal voltage they're high-resistance; at spike voltage they suddenly become low-resistance, shunting the surge to ground.
  • Battery internal resistance: increases as the battery ages — that's why old phones die faster.
Key Takeaway

Ohm's law is not universal. Diodes, LEDs, thermistors, LDRs, varistors all break it — in useful ways! Nonlinearity = the basis of modern electronics.

Section 06

Resistivity of Various Materials

3.7Choosing the Right Material

Materials are classified by their resistivities — spanning 32 orders of magnitude!

ClassResistivity ρ (Ω·m)ExamplesUsed in
Conductors10⁻⁸ – 10⁻⁶Silver (1.6×10⁻⁸), Copper (1.7×10⁻⁸), Gold (2.4×10⁻⁸), Aluminium (2.6×10⁻⁸)Wires, contacts, PCB traces
Alloys~10⁻⁶Nichrome (1.1×10⁻⁶), Manganin (4.8×10⁻⁷), Constantan (4.9×10⁻⁷)Heating elements, standard resistors
Semiconductors10⁻⁵ – 10³Silicon, Germanium, GaAsTransistors, chips, solar cells
Insulators10⁸ – 10¹⁶Glass (10¹⁰ – 10¹⁴), Rubber (10¹³ – 10¹⁵), Diamond (10¹²)Cable insulation, dielectric layers
Real Life Connect
  • Silver is the best conductor (lowest ρ) but too expensive — used only for high-end contacts (switch points, RF cables).
  • Copper is the practical choice — best compromise between cost and conductivity. Used in all house wiring.
  • Aluminium is used in overhead power lines — cheaper and lighter, even though it's slightly worse than copper.
  • Nichrome (Ni-Cr alloy) is the heating element of choice — high ρ, oxidises slowly, melts at high T. Used in toasters, kettles, hair dryers.
  • Manganin / Constantan — special property: their resistance is nearly independent of temperature. Used in standard resistors and precision measuring instruments.
  • Silicon — semiconductor. Its resistivity can be tuned by doping (adding impurities). The foundation of all computer chips.
Why Do Metals Conduct?

Because each metal atom contributes 1–3 "free" electrons to the conduction sea. More free electrons = higher n = lower ρ. Insulators have no free electrons; semiconductors have some, but only at high temperature or with doping.

Key Takeaway

ρ spans 32 orders of magnitude! Silver > copper > gold > aluminium > nichrome > silicon > glass > rubber. Alloys (Nichrome, Manganin) chosen for specific properties — heating or stability. Semiconductors are the foundation of electronics.

Section 07

Temperature Dependence of Resistivity

3.8Why Resistance Changes with Temperature

Heat up a wire — its resistance changes. Why? Two competing effects:

  • More collisions: Higher T → atoms vibrate more → more scattering of electrons → shorter τ → higher ρ. This dominates for metals.
  • More free electrons: Higher T → more electrons can break free → higher n → lower ρ. This dominates for semiconductors.
Temperature Dependence (Metals)

ρ_T = ρ₀[1 + α(T − T₀)]

Where α is the temperature coefficient of resistivity (unit: K⁻¹). For metals, α > 0 (typically 0.003–0.006 K⁻¹).

For semiconductors, α < 0 (resistance decreases with T). For special alloys like Manganin, α ≈ 0 (nearly constant).

V5 · ρ vs T — three behaviours (metal, alloy, semiconductor) METAL (Cu, W) T (K) ρ α > 0 Increases with T ALLOY (Manganin) T (K) ρ α ≈ 0 Nearly constant SEMICONDUCTOR (Si) T (K) ρ α < 0 Decreases with T
Three distinct behaviours — how ρ changes with temperature reveals the nature of the material.
Real Life Connect
  • Incandescent bulb (tungsten): At room temperature R ≈ 15 Ω; when glowing (2700°C), R ≈ 150 Ω — ten times higher! That's why the bulb draws a huge inrush current when first switched on and often burns out at that instant.
  • Thermistors: Deliberately use the strong T-dependence of semiconductors. A tiny bead can measure temperature to 0.01°C precision.
  • Manganin shunts: Used in ammeters — nearly zero α ensures the reading doesn't drift as the ammeter heats up.
  • Superconductors: Below a critical temperature (~92 K for YBCO), ρ suddenly drops to zero. Used in MRI magnets, maglev trains, particle accelerators.
  • Old battery in cold weather: The internal resistance increases with cold — that's why phone batteries die faster in winter.
Exam Trap

Trap: "Temperature coefficient of resistance and resistivity are the same thing."
Correction: For a wire, R = ρℓ/A. If ℓ and A are constant, α_R ≈ α_ρ (the same). But if the wire expands thermally (length increases, area changes), R and ρ change slightly differently. In practice, for small temperature ranges, we use them interchangeably. Just be aware of the subtle difference.

Key Takeaway

ρ_T = ρ₀[1 + α(T−T₀)]. Metals: α > 0 (hotter = more resistance). Semiconductors: α < 0 (hotter = less resistance). Alloys like Manganin: α ≈ 0 (stable). This is why tungsten bulbs have 10× higher resistance when hot.

Section 08

Electrical Energy and Power

3.9Where Does the Energy Go?

Current flowing through a resistor does work against resistance — this energy appears as heat (Joule heating). The power dissipated is:

Electrical Power

P = V·I = I²R = V²/R

Unit: watt (W) = joule/second. All three forms are equivalent — choose the one with known quantities.

Energy over time t: E = P·t (in joules). Bill of ₹ per kWh: 1 kWh = 3.6×10⁶ J.

Power Transmission — Why High Voltage?

The cables from a power station to your home have resistance Rc. The power wasted as heat is Ploss = I²Rc. To minimise loss, we must minimise current I.

But the power delivered is P = VI. So for a given P, higher V means lower I — and lower heat loss!

Transmission Efficiency

Ploss = I²Rc = (P/V)² · Rc

So Ploss ∝ 1/V². Doubling V → one-quarter the loss.

V6 · Power transmission — why high voltage saves energy Low V = 220 V Station Heat loss: lots! I high → P_loss = I²R high Home For P = 100 kW: I ≈ 455 A → huge loss High V = 400,000 V Station I tiny → P_loss tiny Home I ≈ 0.25 A → loss ~10000× less P_loss ∝ 1/V² → high V saves massive energy!
This is why grid transmission uses hundreds of thousands of volts — the same power, but 10,000× less heat loss.
Real Life Connect
  • Electricity bill: Charged in kWh — 1 kWh = 1 unit. A 100 W bulb for 10 hours = 1 kWh.
  • Fuse: A thin wire designed to melt at a set current (P = I²R heats it). Protects circuits from overload.
  • MCB (Miniature Circuit Breaker): Modern alternative to fuses — electromagnetic trip that you can reset.
  • Electric heater / iron / kettle: High-power devices (1000–3000 W) exploit Joule heating for useful work.
  • LED vs incandescent: An LED converts ~90% of power to light (only 10% as heat). An incandescent bulb converts 5% to light, 95% to heat! Switching saves huge amounts of electricity.
  • Power transmission grid: Uses transformers to step-up voltage to 400 kV or 765 kV — reduces losses by millions of watts every kilometre.
  • Supercomputer cooling: CPUs dissipate 100+ W each — cooling systems must remove a few kW per chip.
Common Mistake

Mistake: "P = VI means higher voltage always gives more power."
Correction: For a fixed current, higher V gives more power. But for a fixed load (fixed R), higher V gives more current, hence more power — but from the perspective of the transmission line, we choose high V and low I to keep the same total P.

Mistake: "A resistor with 2× the resistance dissipates 2× the power."
Correction: Depends on whether current or voltage is held constant. If current is fixed: P = I²R → 2× power. If voltage is fixed: P = V²/R → half power! Always check the circuit context.

Key Takeaway

P = VI = I²R = V²/R. Energy = P×t, billed in kWh. Transmission uses high V (low I) to minimise I²R loss. LEDs are vastly more efficient than bulbs because less power goes to heat.

Section 09

EMF, Internal Resistance, and Terminal Voltage

3.10What is a Cell Really Doing?

A cell (or battery) is a device that maintains a potential difference by converting chemical energy into electrical energy. But it's not perfect — it has its own internal resistance r.

EMF (Electromotive Force) — ε

ε = the work done per unit charge by the cell's chemistry

Unit: volt (V). It's NOT a force despite the name — it's a potential difference. Think of it as the "chemical pump pressure" that pushes charge.

ε = V + Ir (when current I flows through the external circuit)

So terminal voltage V = ε − Ir (when the cell is discharging)

Analogy — Water Pump

A cell is like a water pump. The EMF is the pump's "lift capacity" — how high it can push the water. The internal resistance is the pipe friction inside the pump itself. When no water flows (open circuit), pump pressure = EMF. When water flows (closed circuit), some pressure is lost to internal friction → terminal pressure (V) < EMF (ε).

V7 · Real cell with internal resistance — V < ε when current flows + − r R (load) I → V = ε − Ir Terminal voltage = EMF − drop across r V < ε (always, when cell is discharging) V = ε only when I = 0 (open circuit) I = ε / (R + r) Circuit current
A real cell has internal resistance r, so terminal voltage V = ε − Ir is less than EMF ε.
Real Life Connect
  • Car battery: 12 V nominal but 12.6 V when fully charged (open circuit EMF). Cranking the engine drops it to ~10 V due to high current demand (V = ε − Ir with big I).
  • Phone at low battery: EMF falls and internal resistance rises as the cell ages — hence faster discharge.
  • Short circuit danger: If R → 0, I = ε/r — huge current, dangerous. That's why fuses blow instantly when there's a short.
  • LED torch: If you put a 3.7 V Li-ion cell directly on a 2 V red LED, current explodes (limited only by r and LED's internal resistance) → LED burns out. Always use a current-limiting resistor.
  • Jump-starting a car: The starter draws 200+ A from the battery. Due to internal resistance, even a good battery's terminal voltage sags during cranking.
Common Mistake

Mistake: "EMF is a force."
Correction: Despite the name, it's measured in volts — it's a potential difference, not a force. Name is historical; no one knows why it stuck.

Mistake: "V = ε always."
Correction: Only in an open circuit (I = 0). When current flows, V = ε − Ir < ε. The drop Ir is due to the cell's internal resistance.

Key Takeaway

EMF = the cell's chemical "pump pressure" (in volts). Terminal V = ε − Ir when current flows. I = ε/(R+r). Internal resistance causes heat in the battery itself — that's why it gets warm at high current.

Section 10

Cells in Series and Parallel

3.11Combining Batteries

Cells in Series

Battery cells stacked end-to-end. The EMFs add, internal resistances add. Current is the same through all.

Series Combination (n cells)

εeq = ε₁ + ε₂ + … + εₙ (if all aligned same way)

req = r₁ + r₂ + … + rₙ

If one cell is reversed: εeq = ε₁ + ε₂ − ε₃ + … (subtract the reversed one)

Cells in Parallel

Cells connected + to + and − to −. Voltages equal, currents add. Used when you want more current without raising voltage.

Parallel Combination (2 cells)

εeq = (ε₁r₂ + ε₂r₁)/(r₁+r₂)

req = r₁r₂/(r₁+r₂)

Special case (identical cells): εeq = ε, req = r/n

V8 · Series vs parallel cells Series: EMFs add, r add ε₁ r₁ ε₂ r₂ ε₃ r₃ ε_eq = ε₁ + ε₂ + ε₃ r_eq = r₁ + r₂ + r₃ Higher voltage, same current Parallel: same V, currents add ε₁ ε₂ ε₃ ε_eq = ε (if identical) r_eq = r/n (if identical) Same voltage, more current capacity
Real Life Connect
  • TV remote / torch: 2 AA cells in series (1.5 V + 1.5 V = 3 V). Series is common because most devices need higher voltage than a single cell provides.
  • Car battery: Six 2 V lead-acid cells in series = 12 V. Each cell handles huge current, but voltages add.
  • Laptop battery pack: 3–4 Li-ion cells in series = 11–15 V, but also often in parallel to boost capacity (Ah).
  • Solar panel arrays: Cells in series for higher voltage (to charge 12 V batteries), panels in parallel for more current. Real PV systems use both combinations.
  • Emergency lights: Use parallel cells for redundancy — if one fails, others still work.
Exam Trap

Trap: "More cells in series always means more current."
Correction: No! Adding cells in series increases EMF and internal resistance (r_eq = Σr). The current I = ε_eq/(R + r_eq) — it might even decrease if R is very small compared to r. Check the numbers!

Optimal combination: For maximum current through R: if R > r, use series. If R < r, use parallel. This is a classic board question.

Key Takeaway

Series: ε adds, r adds — boosts voltage. Parallel: ε same (or weighted avg), r reduces — boosts current capacity. For maximum current through load R: series when R > r, parallel when R < r. Mix and match to fit the application.

Section 11

Kirchhoff's Rules

3.12Solving Any Circuit

Ohm's law is enough for simple circuits, but real circuits have branches. Kirchhoff's two rules let you solve any circuit — a physicist's universal key.

Kirchhoff's Junction Rule (KCL)

Σ Current entering a junction = Σ Current leaving

Also called "conservation of charge" — charge can't pile up at a junction.

Kirchhoff's Loop Rule (KVL)

Σ Voltage changes around any closed loop = 0

Also called "conservation of energy" — going around a loop brings you back to the same potential.

Sign convention:

  • Going with current through R: ΔV = −IR
  • Going against current through R: ΔV = +IR
  • Going − to + through a cell: ΔV = +ε
  • Going + to − through a cell: ΔV = −ε
V9 · Junction rule — charges can't pile up J I₁ (in) I₂ (in) I₃ (out) I₄ (out) I₁ + I₂ = I₃ + I₄ Charge conservation at every junction
V10 · Loop rule — sum of voltage changes around a closed loop = 0 + ε R₂ R₁ I (direction) +ε − IR₂ − IR₁ = 0 Energy conservation: sum of voltage changes = 0
Real Life Connect
  • Every electronic device — from your phone to a satellite — uses Kirchhoff's rules in its design. Circuit simulators like SPICE are essentially solving Kirchhoff's equations numerically.
  • House wiring analysis: Electricians use Kirchhoff to trace why a fuse blew or a light flickers in a multi-circuit home.
  • PCB design: Every trace on a circuit board must satisfy KCL and KVL. Software checks automatically.
  • Battery management systems in EVs: Apply Kirchhoff to hundreds of cells to balance charge and monitor health.
Why Two Rules?

KCL (junction) is about charge conservation — no charge piles up. KVL (loop) is about energy conservation — you can't get free energy by going around in circles. Together they give a complete set of equations for any circuit: use KCL at every junction, KVL at every independent loop, and solve the linear system.

Exam Trap

Trap: "Sign convention of IR drops."
Remember: going WITH current through R → −IR (potential drops). Going AGAINST current → +IR (potential rises). Going − to + through a cell → +ε (gain energy). Going + to − → −ε. Be consistent — flip signs and the equations will be wrong.

Key Takeaway

KCL: ΣI_in = ΣI_out (charge conservation). KVL: ΣΔV = 0 around loop (energy conservation). These two rules solve any circuit. Combined with Ohm's law, they're the complete toolkit.

Section 12

Wheatstone Bridge

3.13Measuring Resistance Precisely

The Wheatstone bridge is an elegant application of Kirchhoff's rules. It's used to measure an unknown resistance with high precision — a lab classic and the basis of many modern sensors.

Wheatstone Bridge Balance Condition

R₁ / R₂ = R₃ / R₄

When balanced, the galvanometer (between the two junctions) shows zero current. Then you can calculate an unknown resistance from the other three.

Cross-multiplied: R₁·R₄ = R₂·R₃

V11 · Wheatstone bridge — at balance, no current through G B D A C R₁ R₂ R₃ R₄ G I_g = 0 (at balance) V Balance: R₁/R₂ = R₃/R₄ Then R₁R₄ = R₂R₃
Balance = no current through the galvanometer — a precise null-detection method.
Real Life Connect
  • Meter bridge: A practical version of the Wheatstone bridge using a 1 m wire with a sliding jockey. Standard school experiment.
  • Strain gauges: Two arms of a Wheatstone bridge are bonded to a metal beam. When the beam bends, one gauge stretches (increases R), the other compresses (decreases R) — the imbalance gives a voltage proportional to strain. Used in weighing scales, torque sensors, aircraft wing testing.
  • Temperature sensors (RTDs): A platinum resistance thermometer uses a Wheatstone bridge — change in R of platinum gives a voltage proportional to temperature.
  • Pressure sensors: Piezoresistive pressure sensors in cars, phones, and industrial equipment all rely on Wheatstone bridge configurations.
  • Humidity sensors: Bridge with a humidity-sensitive resistor — unbalanced voltage gives humidity reading.
  • Medical instrumentation: Blood pressure monitors, pulse oximeters, ECG leads — all use Wheatstone bridge circuits.
Why is the Wheatstone bridge so Precise?

Because it uses null detection — you adjust until the galvanometer reads zero. At balance, no current flows through the meter, so its own resistance doesn't matter. The measurement depends only on the ratio of known resistors. This eliminates systematic errors from the meter — much more accurate than just measuring V and I separately.

Key Takeaway

Wheatstone bridge: at balance (I_g = 0), R₁/R₂ = R₃/R₄. Uses null detection — extremely precise. Basis of the meter bridge (school experiment) and countless modern sensors (strain, temperature, pressure).

Practice

📝 Solved Examples with Step Marking

📋 2 Marks

Q1. A current of 5 A flows through a conductor for 10 s. How much charge has passed?

Given ½ Mark

I = 5 A, t = 10 s

Formula ½ Mark

Q = I × t

Compute 1 Mark

Q = 5 × 10 = 50 C

Q = 50 C
📋 3 Marks

Q2. A wire has resistance 10 Ω, length 2 m, and cross-section 10⁻⁶ m². Find the resistivity of the material.

Given ½ Mark

R = 10 Ω, ℓ = 2 m, A = 10⁻⁶ m²

Formula ½ Mark

R = ρℓ/A → ρ = RA/ℓ

Compute 1½ Marks

ρ = (10 × 10⁻⁶)/2 = 5 × 10⁻⁶ Ω·m

Unit check ½ Mark

Ω·m ✓

ρ = 5 × 10⁻⁶ Ω·m
📋 3 Marks

Q3. A cell of EMF 12 V and internal resistance 1 Ω is connected to a 5 Ω resistor. Find the current and terminal voltage.

Given ½ Mark

ε = 12 V, r = 1 Ω, R = 5 Ω

Current 1 Mark

I = ε/(R+r) = 12/(5+1) = 2 A

Terminal voltage 1 Mark

V = ε − Ir = 12 − (2)(1) = 10 V
Alternatively V = IR = 2×5 = 10 V ✓

Comment ½ Mark

Terminal voltage is less than EMF — the missing 2 V is dissipated inside the cell (heat).

I = 2 A, V = 10 V
📋 4 Marks

Q4. Two cells of EMFs 5 V and 3 V with internal resistances 1 Ω and 2 Ω are connected in parallel. Find the equivalent EMF and internal resistance.

Given ½ Mark

ε₁ = 5 V, r₁ = 1 Ω; ε₂ = 3 V, r₂ = 2 Ω

Equivalent EMF formula ½ Mark

ε_eq = (ε₁r₂ + ε₂r₁)/(r₁+r₂)

Compute ε_eq 1 Mark

ε_eq = (5·2 + 3·1)/(1+2) = (10+3)/3 = 13/3 ≈ 4.33 V

Equivalent resistance 1 Mark

r_eq = r₁r₂/(r₁+r₂) = (1·2)/3 = 2/3 ≈ 0.67 Ω

Note 1 Mark

ε_eq is between the two EMFs, closer to the one with lower r (the "stronger" cell). r_eq is smaller than either r.

ε_eq ≈ 4.33 V, r_eq ≈ 0.67 Ω
📋 3 Marks

Q5. An electric bulb is rated 100 W, 220 V. Find (a) its resistance, (b) current at rated voltage, (c) power consumed if connected to 110 V.

Given ½ Mark

P = 100 W, V = 220 V

(a) Resistance ½ Mark

R = V²/P = (220)²/100 = 48400/100 = 484 Ω

(b) Rated current ½ Mark

I = P/V = 100/220 ≈ 0.455 A

(c) Power at 110 V 1 Mark

P' = V'²/R = (110)²/484 = 12100/484 ≈ 25 W

Insight ½ Mark

Halving the voltage quarters the power (P ∝ V²). This is why dimmers work — they lower the RMS voltage to dim the bulb.

R = 484 Ω, I = 0.455 A, P = 25 W at 110 V
📋 4 Marks

Q6. In a Wheatstone bridge, R₁ = 4 Ω, R₂ = 8 Ω, R₃ = 6 Ω. What value of R₄ will balance the bridge?

Balance condition ½ Mark

R₁/R₂ = R₃/R₄

Solve 1 Mark

4/8 = 6/R₄

4R₄ = 48

R₄ = 12 Ω

Verify ½ Mark

R₁×R₄ = 4×12 = 48; R₂×R₃ = 8×6 = 48 ✓

Bonus 2 Marks

At balance, no current flows through the galvanometer between B and D. This means V_B = V_D. Kirchhoff's laws give zero potential drop between them. Good for null detection in the lab.

R₄ = 12 Ω
📋 5 Marks

Q7. A copper wire has ρ = 1.7×10⁻⁸ Ω·m and cross-section 10⁻⁶ m². A current of 2 A flows through it. If the free electron density is n = 8.5×10²⁸ m⁻³, find the drift velocity.

Given ½ Mark

ρ = 1.7×10⁻⁸ Ω·m, A = 10⁻⁶ m², I = 2 A, n = 8.5×10²⁸ m⁻³, e = 1.6×10⁻¹⁹ C

Formula ½ Mark

I = neAv_d → v_d = I/(neA)

Compute denominator 1 Mark

neA = 8.5×10²⁸ × 1.6×10⁻¹⁹ × 10⁻⁶
= 1.36×10⁻³ × 10⁶ = 1.36×10³

Drift velocity 1 Mark

v_d = 2 / 1.36×10³
= 1.47×10⁻³ m/s
= 1.47 mm/s

Comment 1 Mark

That's slower than a walking ant! Yet the lamp lights instantly because the field propagates at ~c.

Sanity check 1 Mark

Typical drift velocity for ~1 A copper wire: 0.1–1 mm/s ✓

v_d ≈ 1.47 mm/s
Quick Reference

📐 Complete Formula Sheet

Chapter 3 — All Formulas on One Page

Current
I = Q/t = dQ/dt
Current in a Wire
I = n·e·A·v_d
Ohm's Law
V = IR
Resistance
R = ρℓ/A
Current Density
j = I/A = σE
Conductivity
σ = 1/ρ
Drift Velocity
v_d = eEτ/m = eVτ/(mL)
Resistivity (Microscopic)
ρ = m/(ne²τ)
Mobility
μ = v_d/E = eτ/m
Temperature Dependence
ρ_T = ρ₀[1 + α(T−T₀)]
Electrical Power
P = VI = I²R = V²/R
Energy
E = Pt = VIt = I²Rt
Transmission Loss
P_loss = I²R_c = (P/V)²R_c
EMF & Terminal V
V = ε − Ir
Circuit Current
I = ε/(R + r)
Cells in Series
ε_eq = Σε_i, r_eq = Σr_i
Cells in Parallel (2 cells)
ε_eq = (ε₁r₂+ε₂r₁)/(r₁+r₂), r_eq = r₁r₂/(r₁+r₂)
Kirchhoff Junction
ΣI_in = ΣI_out
Kirchhoff Loop
ΣΔV = 0
Wheatstone Balance
R₁/R₂ = R₃/R₄
Constants
e = 1.6×10⁻¹⁹ C, m = 9.11×10⁻³¹ kg

📖 Notation Key

IElectric current (A)
VVoltage / potential difference (V)
RResistance (Ω)
ρResistivity (Ω·m)
σConductivity (S/m)
jCurrent density (A/m²)
nFree carrier density (m⁻³)
eElectron charge = 1.6×10⁻¹⁹ C
τRelaxation time (s)
v_dDrift velocity (m/s)
μMobility (m²/V·s)
αTemperature coefficient (K⁻¹)
εEMF (V)
rInternal resistance (Ω)
Test Yourself

✍️ MCQ Practice

Score: 0 / 12
New Pattern

🎯 Assertion–Reason

(A) Both true, R explains A. (B) Both true, R does NOT explain A. (C) A true, R false. (D) A false, R true.

Score: 0 / 6