Home/ Physics/ Chapter 7 — Alternating Current
Class 12 Physics · Chapter 7 · Enhanced Edition

Alternating Current

From the AC that powers your home to the resonance that tunes your radio — with deep explanations, animated phasors, an interactive LCR resonance simulator, 3D transformer, 20+ real-life examples, and a printable formula sheet.

9Concepts
22+Real-life Examples
10Diagrams
1Simulators
The Big Picture

🗺️ How Everything Connects

Before diving into individual sections, here's the entire chapter on one page. Use this as a mental map — every topic is a link in this chain.

AC Basics v = v_m sin ωt Phasors Rotating vectors R, L, C reactances Series LCR Z, φ Power P = VI cosφ Transformers Step up/down Resonance Power Factor "Peak response at ω₀" "Real vs apparent power" Key applications of LCR physics
Key Takeaway

AC is a sinusoidal voltage/current. Phasors make AC calculations easy (no trigonometry needed). R, L, C each respond differently — resistance, inductive reactance, capacitive reactance. In series LCR, they combine into impedance Z with phase angle φ. Resonance occurs when X_L = X_C. Transformers use mutual inductance for efficient power distribution.

Section 01

Alternating Current — Basics

7.1–7.2What is AC and Why Do We Use It?

Alternating current (AC) is current that periodically reverses direction. Unlike DC (direct current) which flows steadily one way, AC flows back and forth — typically 50 or 60 times per second. It's the type of electricity that comes out of every wall socket in your home.

AC Voltage Equation

v(t) = vm · sin(ωt) (or cos(ωt), depending on phase reference)

Where:

  • vm = peak (maximum) voltage
  • ω = angular frequency (rad/s) = 2πf
  • f = frequency (Hz) — 50 Hz in India, 60 Hz in USA
  • T = 1/f = period (20 ms for 50 Hz)

RMS Values — The "Effective" AC

Because AC alternates, its average is zero. So how do we talk about "220 V" from a wall socket? That's the RMS (root-mean-square) value:

RMS (Root-Mean-Square) Values

Vrms = vm / √2 ≈ 0.707 vm

Irms = im / √2 ≈ 0.707 im

Meaning: Vrms is the DC voltage that would produce the same heating effect (Joule heating) in a resistor.

Household "220 V AC" means Vrms = 220 V, so the peak voltage is vm = 220 × √2 ≈ 311 V!

V1 · AC waveform — RMS vs peak voltage t v(t) v_m = 311 V (peak) V_rms = 220 V (RMS) −v_m 0 T/2 T 3T/2 2T Household "220 V AC" → Peak = 311 V, Frequency = 50 Hz, Period = 20 ms
Real Life Connect
  • Household electricity: 220 V RMS, 50 Hz in India/Europe; 120 V, 60 Hz in USA. Every appliance (fan, TV, fridge) uses this.
  • Why AC over DC? AC voltage can be easily stepped up/down using transformers. This makes long-distance transmission efficient (high voltage, low current → low loss).
  • Your phone charger: AC from wall → transformer steps down → rectifier converts to DC → charges your phone. Internally, 3 stages!
  • AC motors: Induction motors (in fans, refrigerators, washing machines) run directly on AC — cheap, durable, brushless.
  • Fluorescent lights and LEDs: Both work on AC (LEDs have driver circuits to convert to DC internally).
  • Electric trains: Use 25 kV AC from overhead lines, transformed down to a few hundred volts for the traction motors.
Why is RMS Useful?

Because power dissipation (heating) depends on the square of current: P = I²R. Average of i² over a cycle is i_m²/2, so the "effective" current is i_m/√2 = I_rms. This means V_rms × I_rms × cosφ = average power — a beautiful equivalence. Household appliances are rated for RMS, not peak. When a bulb says "100 W, 220 V", it means at V_rms = 220 V it consumes 100 W on average.

Common Mistake

Mistake: "The 220 V from the wall is the peak voltage."
Correction: 220 V is the RMS value. Peak = 220√2 ≈ 311 V. The actual voltage swings from +311 V to −311 V, 50 times per second.

Mistake: "I can just add AC voltages like DC."
Correction: AC voltages must be added as phasors (vectors) because they have phase. 100 V + 100 V of AC may give anything from 0 V to 200 V depending on phase difference!

Key Takeaway

AC: v = v_m sin(ωt). RMS = peak/√2 ≈ 0.707×peak. Household "220 V" is RMS; peak is 311 V. AC is used because transformers can step it up/down for efficient transmission.

Section 02

Phasors — Representing AC as Rotating Vectors

7.3AC Analysis Made Visual

Adding AC voltages with different phases needs trig identities — messy. Instead, physicists use phasors: rotating vectors whose projection onto the vertical axis gives the AC quantity.

Phasor

A phasor is a vector of length equal to the amplitude (peak value), rotating counter-clockwise at angular frequency ω. Its vertical projection at any time t gives the instantaneous value of the AC quantity.

Examples:

  • Phasor V of length v_m rotating at ω → projection = v_m sin(ωt)
  • Phasor I of length i_m rotating at ω → projection = i_m sin(ωt + φ)

Key insight: For AC circuits, all phasors rotate at the same ω. So we can "freeze" them at any instant and just work with their relative angles!

V2 · Rotating phasors — projection = instantaneous AC value x y V I θ Phasor diagram Waveform (projection vs time) V(t) I(t) ωt Each phasor rotates at ω, but they stay locked at fixed relative angle θ
Phasors freeze AC into vectors at their relative angles — much easier to add than trig functions.
Analogy — Clock Hands

Imagine two clock hands moving at the same speed (same ω) but offset by some angle. Their "vertical heights" (projections) give two sinusoidal waves of the same frequency but different phase. That's exactly what phasors are. Adding phasors = adding the hands as vectors; the result is another hand (also rotating at ω) that represents the combined AC voltage.

Real Life Connect

Power grid operators use phasor measurement units (PMUs) to monitor the entire national grid in real-time. Phasors at different substations must stay synchronized — if the phase drifts too far apart, circuit breakers trip to prevent blackouts. Thousands of PMUs monitor phasors across continents.

3-phase power (used in industry) is exactly this: three AC voltages 120° apart in phase, so that their sum is always zero. Motors run smoothly because one phase is always "on".

Key Takeaway

Phasors represent AC as rotating vectors at ω. Vertical projection = instantaneous value. Add/subtract AC voltages using vector rules instead of trig. Same frequency → relative angles fixed → easy geometry.

Section 03

AC through a Resistor

7.2V and I in Phase

The simplest AC circuit — just a resistor R. Ohm's law works at every instant:

AC in a Resistor

If v = vm sin(ωt), then:

i = v/R = (vm/R) sin(ωt) = im sin(ωt)

im = vm/R

V and I are in phase — they reach peaks, zero, and troughs together.

V3 · Resistor: V and I are in phase V, I (same direction) Phasor V(t) i(t) V and I reach max, zero, min at the SAME time — in phase (φ = 0)
Real Life Connect

Electric heaters, incandescent bulbs, and toasters are essentially resistive loads. They draw current in phase with the voltage, and dissipate power as heat. This is the simplest and most efficient way to convert electricity to heat — 100% of power goes to heating.

Why "pure resistance" is rare in practice: Every real circuit has some inductance (wires, coils) and capacitance (parallel wires). Only at very low frequencies (like DC or 50 Hz for small circuits) can we treat loads as purely resistive.

Key Takeaway

AC in a resistor: V and I are in phase. i_m = v_m/R. Power dissipated = same as DC (using RMS values).

Section 04

AC through an Inductor

7.4Current LAGS Voltage by 90°

An inductor resists changes in current. When AC voltage is applied, the current can't "keep up" — it lags behind the voltage.

AC in an Inductor

If v = vm sin(ωt), then:

i = im sin(ωt − π/2) (current lags by 90°)

im = vm / XL, where XL = ωL (inductive reactance)

Unit: ohm (Ω). Reactance is like "AC resistance" but depends on frequency.

Inductive Reactance — Key Properties

XL = ωL = 2πfL

  • Proportional to frequency: at high f, X_L is large (blocks fast signals)
  • Zero at DC (f = 0): inductors pass DC freely
  • Grows with inductance: bigger coil = more opposition

Average power dissipated = 0 (reactance doesn't dissipate energy — it stores and returns it each cycle).

V4 · Inductor: current lags voltage by 90° V I 90° Phasor: I lags V by 90° V(t) i(t) V peaks first → I peaks 90° later ("current lags")
Real Life Connect
  • Fluorescent light chokes: A fluorescent tube needs a choke (inductor) in series to limit current. Its X_L stabilizes the current despite voltage fluctuations.
  • Audio crossover networks: In speakers, inductors block high frequencies from reaching a woofer — only low bass passes. Uses X_L = ωL.
  • Power supply filters: Inductors in DC power supplies (chokes) block the high-frequency ripple, letting only smooth DC through.
  • Induction motors: Work on the principle that current in the rotor lags the stator field — creating torque.
  • Ferrite beads on cables: Tiny inductors clip onto USB cables to absorb high-frequency noise — X_L at high frequencies blocks those noise currents.
Analogy — Heavy Flywheel

An inductor is like a heavy flywheel. When you try to spin it up (apply voltage), it "resists" the change. The current can't change instantly — it lags behind the applied force. Similarly, an inductor smooths current fluctuations like a flywheel smooths rotational speed.

Key Takeaway

Inductor: current lags voltage by 90°. X_L = ωL (grows with frequency). Zero power dissipation. Blocks high frequencies, passes DC. Basis of chokes, crossovers, filters.

Section 05

AC through a Capacitor

7.5Current LEADS Voltage by 90°

A capacitor stores charge. When AC voltage changes sign, current must flow to charge/discharge the plates — so current has to "rush in" before voltage builds up.

AC in a Capacitor

If v = vm sin(ωt), then:

i = im sin(ωt + π/2) (current leads by 90°)

im = vm · ωC = vm / XC, where XC = 1/(ωC) (capacitive reactance)

Unit: ohm (Ω).

Capacitive Reactance — Key Properties

XC = 1/(ωC) = 1/(2πfC)

  • Inversely proportional to frequency: at high f, X_C is small (passes fast signals)
  • Infinite at DC (f = 0): capacitor blocks DC completely
  • Decreases with capacitance: bigger capacitor = less opposition

Average power dissipated = 0 (reactance stores and returns energy each cycle).

V5 · Capacitor: current leads voltage by 90° V I 90° Phasor: I leads V by 90° V(t) i(t) I peaks first → V peaks 90° later ("current leads")
Real Life Connect
  • Capacitive touchscreens: Your finger changes the local capacitance, altering the current drawn by the touch electrodes. The IC detects this — a form of AC capacitive sensing.
  • Blocking capacitors: Used to block DC while passing AC — common in audio circuits (blocks DC offsets while letting the audio signal through).
  • Decoupling capacitors: Place near ICs to provide fast AC current, filtering out high-frequency noise. X_C small at high f means easy path for noise.
  • Audio crossover networks: Capacitors block low frequencies from reaching tweeters — only high frequencies pass (X_C small at high f).
  • Power factor correction: Industrial loads are inductive; utilities add capacitor banks to correct their power factor. We'll see this in Section 7.
  • Electric fences: Use capacitor discharge to deliver pulses — the capacitor charges slowly, then dumps a pulse. AC trickery!
Analogy — Elastic Balloon

A capacitor is like a balloon. When you push air into it (apply voltage), the balloon stretches to store air. When you release, air rushes out — like current flowing. The current (air flow) has to lead the voltage (balloon pressure) because air flows in while the balloon is filling, but the balloon's pressure only builds up after.

Key Takeaway

Capacitor: current leads voltage by 90°. X_C = 1/(ωC). Decreases with frequency. Zero power dissipation. Blocks DC, passes high frequencies. Basis of capacitive touchscreens, filters, crossovers, decoupling.

Section 06

Series LCR Circuit

7.6Combining R, L, C

Now put R, L, C in series. Same current flows through all three, but each element produces a different voltage and phase relationship.

Series LCR — Key Formulas

Impedance Z = √(R² + (XL − XC)²)

Current amplitude: im = vm/Z

Phase angle: φ = tan⁻¹((XL − XC)/R)

Where XL = ωL and XC = 1/(ωC).

  • If XL > XC: circuit is inductive — current LAGS voltage (φ > 0)
  • If XC > XL: circuit is capacitive — current LEADS voltage (φ < 0)
  • If XL = XC: circuit is resonant — current and voltage IN PHASE (φ = 0)
V6 · LCR phasor diagram — impedance triangle I V_R V_L V_C V φ Phasor: V = V_R + V_L + V_C R X_L − X_C Z φ Impedance triangle Z = √(R² + (X_L − X_C)²)  |  tanφ = (X_L − X_C)/R

Interactive: LCR Circuit Frequency Simulator

LCR Simulator — how does frequency affect impedance and phase?

Inductive X_L (Ω)
31.4
Capacitive X_C (Ω)
63.7
Impedance Z (Ω)
50.9
Phase φ (°)
-40.1
Current i_m (A)
2.16
Circuit type
Capacitive
Try: f = 10 Hz (cap dominates) → f ≈ 71 Hz (resonance, Z=R) → f = 500 Hz (inductor dominates)
Real Life Connect
  • Every electronic device: Circuit boards are full of LCR networks. Filters, oscillators, and impedance matching all use the same math.
  • Speaker crossovers: A combination of L and C routes low frequencies to the woofer and high frequencies to the tweeter. Series LCR at work.
  • Radio tuners: Variable capacitor plus fixed inductor → LCR circuit resonates at the tuned frequency. This is how old-school radios select stations!
  • Anti-resonance in power systems: Utilities avoid certain L-C combinations because they can resonate at harmonic frequencies and cause overvoltages.
  • EMI filters: Every USB and power supply has an LC filter to keep noise from escaping or entering.
Common Mistake

Mistake: "Z = R + X_L + X_C."
Correction: No! Impedances add as vectors: Z = √(R² + (X_L − X_C)²). R is orthogonal to X_L and X_C. You cannot just add them numerically.

Mistake: "Current is maximum at low frequency."
Correction: At low f, X_C dominates (large), so current is SMALL. At high f, X_L dominates, current is also SMALL. Current is maximum at resonance where X_L = X_C (both cancel).

Key Takeaway

Series LCR: Z = √(R² + (X_L−X_C)²). Current i_m = v_m/Z. Phase φ = tan⁻¹((X_L−X_C)/R). Inductive if X_L > X_C, capacitive if X_C > X_L. Impedance is a vector sum, not scalar. This is the foundation of every filter and tuning circuit.

Section 07

Resonance — When LCR Sings

7.6.2The Magic Frequency

At one specific frequency, X_L exactly equals X_C — they cancel! Impedance drops to minimum, current peaks. This is resonance.

Resonant Frequency

Condition: XL = XC

ω₀ = 1/√(LC)  |  f₀ = 1/(2π√(LC))

At resonance:

  • Z = R (minimum — only resistance)
  • i_m = v_m/R (maximum current)
  • φ = 0 (current and voltage in phase)
  • Power factor = 1 (maximum power transferred)
V7 · Resonance curve — current vs frequency Frequency ω → Current i_m → Resonance ω₀ ω₀ = 1/√(LC) Capacitive (X_C > X_L) Inductive (X_L > X_C) Small R (sharp peak) Large R (broad peak)
At resonance, current peaks; the sharper the peak, the "higher Q" the circuit. Radio tuners exploit this to select one station.
Q-Factor (Quality Factor)

Q = ω₀L/R = 1/(ω₀RC) = (1/R)·√(L/C)

Measures "sharpness" of resonance. Higher Q = sharper peak = more selective. Radio receivers use high-Q circuits for good tuning.

Also: Q = (voltage across L or C at resonance) / (applied voltage). In a high-Q circuit, this can be huge — 100× typical.

Real Life Connect — Resonance in Action
  • Radio tuning: Your radio's tuning dial varies a capacitor to change f₀. Only the station matching f₀ gets amplified (resonates); others are filtered out.
  • TV antennas: Precisely tuned LCR circuits select one channel from the thousands of signals in the air.
  • MRI scanners: The RF coil resonates at the Larmor frequency of hydrogen nuclei (e.g., 64 MHz for 1.5 T MRI) — sending/receiving signals only at that frequency.
  • WiFi and Bluetooth: Antennas and matching circuits are tuned to resonate at 2.4 GHz or 5 GHz — the WiFi frequencies.
  • Metal detector: A high-Q LCR circuit resonates; when metal is nearby, eddy currents change the effective L, shifting resonance. The shift is detected.
  • Loudspeaker cabinets: The Helmholtz resonance of a speaker port is tuned to extend bass response — the same physics!
  • Musical instruments: A violin body, guitar soundbox, and flute are all acoustic resonators — the same idea for sound instead of AC.
Why Does Resonance Occur?

Physically, at f₀, the capacitor's voltage and inductor's voltage are equal and opposite at every moment. They "cancel" each other in the circuit, leaving only R. It's like a swing pushed at exactly its natural frequency — each push adds energy. In LCR, the inductive and capacitive energies oscillate back and forth between each other, and the applied source only needs to supply the resistive losses.

Key Takeaway

Resonance: X_L = X_C, so ω₀ = 1/√(LC). Z = R (minimum), i = v_m/R (maximum), φ = 0. Q-factor measures sharpness. Basis of radio/TV tuning, WiFi, MRI. Every filter and antenna you use exploits resonance!

Section 08

Power in AC Circuits

7.7Real vs Reactive Power

In AC circuits, average power isn't simply VI — you need to account for the phase angle between V and I.

AC Power

P = Vrms · Irms · cos φ

Where φ = phase angle between V and I. cos φ is called the power factor.

In terms of impedance: cos φ = R/Z

So: P = I²rms · R (only resistance dissipates power!)

Power Factor

PF = cos φ = R/Z

  • PF = 1 (φ = 0): pure resistance, maximum power transfer. Best case.
  • PF = 0 (φ = ±90°): pure L or C, no average power dissipated ("wattless current").
  • 0 < PF < 1: real LCR circuits — partial power transfer.
V8 · Power triangle — real, reactive, apparent power Real Power P = VI cosφ (W) Reactive Q = VI sinφ (VAR) Apparent Power S = VI (VA) φ Meaning: P: real work (heat, motion) Q: sloshes back-forth S: what's "delivered" cos φ: PF Only P does useful work Q bounces between L and C High PF = efficient
Real Life Connect — Power Factor Matters!
  • Industrial electricity bills: Factories with low PF pay penalties to the utility — they draw more current than they need to. Utilities add capacitor banks to correct PF to near 1.
  • Why correction matters: A factory with 100 kW load at PF=0.7 draws 143 A. At PF=0.95, it draws only 105 A. The wires and transformers can be smaller (cheaper), and the losses (I²R) drop dramatically.
  • Fridge/fan motors: These are inductive loads with PF ~ 0.6–0.8. Their cables need to be rated for more current than just the "real power" would suggest.
  • LED bulbs: Modern electronic ones correct PF internally to near 1. Old "non-PF-corrected" cheap LEDs have poor PF and waste power.
  • Wattless current (φ = 90°): In pure L or C, current flows but does no work — a curiosity. This is why utilities can't just bill by apparent power!
Why Only Resistance Dissipates Power?

Because inductors and capacitors store energy in their fields, then give it back. Over a full cycle, the net energy absorbed is zero. Power flows into them (charging) and back out (discharging) — that's the "reactive power" Q. Only R converts energy to heat that's truly gone.

That's why transformers can be 99% efficient (they're mostly reactive) but resistive heaters are only 99% efficient (heat escapes).

Key Takeaway

AC power P = V_rms I_rms cosφ. Only resistance dissipates real power. Power factor cos φ = R/Z. PF = 1 is ideal; PF = 0 is wasted. Industries pay penalties for low PF → corrected with capacitors. Real power P = I²R always.

Section 09

Transformers — Changing Voltage, Saving Power

7.8How Electricity Reaches Your Home

A transformer uses mutual inductance to change AC voltage from one level to another. This is how the electricity from a power plant (which generates ~20 kV) reaches your home (at 220 V) — through a series of step-up and step-down transformers.

Transformer Basics

Two coils (primary Np turns, secondary Ns turns) on a shared iron core.

Voltage ratio: Vs/Vp = Ns/Np

Current ratio: Is/Ip = Np/Ns (ideal, 100% efficient)

  • Step-up: Ns > Np → Vs > Vp, Is < Ip
  • Step-down: Ns < Np → Vs < Vp, Is > Ip

Power is conserved: Pp = Ps (in ideal transformer).

V9 · Transformer — iron core couples two coils Primary N_p = 100 turns Secondary N_s = 200 turns shared magnetic flux V_s/V_p = N_s/N_p = 2
This example: 100 → 200 turns = step-up transformer (doubles voltage, halves current)

Transformer Losses (Real vs Ideal)

Loss TypeCauseReduction Method
Copper lossI²R heating in coil windingsUse thick wire for high-current windings
Eddy current lossCirculating currents in iron coreLaminate the core (thin insulated sheets)
Hysteresis lossRepeated magnetisation/demagnetisation of coreUse soft iron with low hysteresis (e.g., silicon steel)
Flux leakageSome field lines miss the secondaryWind coils close together on the same core limb
Real Life Connect — Transformers in Your World
  • Power grid transmission: Generator (11 kV) → Step-up to 400 kV → transmit across country → step-down to 220 V at substation → home. Multiple transformers at every stage!
  • Why high voltage for transmission? Power loss = I²R. Same power at higher V means lower I (P = VI). So step up to 400 kV for transmission → current drops 36× → losses drop 1300×!
  • Your phone charger: Inside: a small transformer converts 220V AC to ~5V AC, then rectifier converts to DC for the battery.
  • Laptop power brick: Has a switched-mode transformer running at ~50 kHz (much smaller than 50 Hz transformers of same power rating — higher frequency = smaller core).
  • Current transformers (CTs) and potential transformers (PTs): Used in power stations to scale down high voltages/currents to measurable levels for metering and protection.
  • Isolation transformers: 1:1 ratio, used for safety — separate circuits electrically. Common in medical equipment and lab benches.
  • Welding transformers: Step-down to a few volts but hundreds of amps — enough to melt metal.
Exam Trap

Trap: "Step-up transformer increases power."
Correction: No! Transformers conserve energy (ideal) — they can't increase power. Step-up increases voltage but decreases current by the same factor. P = VI stays constant. This is a very common misconception!

Trap: "Transformers work on DC."
Correction: Transformers need changing magnetic flux (Faraday's law). DC gives constant flux → no EMF in secondary. Only AC works!

Key Takeaway

Transformer: mutual inductance changes AC voltage. V_s/V_p = N_s/N_p, I_s/I_p = N_p/N_s. Power conserved (ideal). Step up = higher V, lower I. Step down = lower V, higher I. Only works on AC! Losses: copper (I²R), eddy (laminations), hysteresis (soft iron), flux leakage (close winding).

Practice

📝 Solved Examples with Step Marking

📋 2 Marks

Q1. An AC voltage has peak value 311 V at frequency 50 Hz. Find its RMS value and write its equation.

Given ½ Mark

v_m = 311 V, f = 50 Hz, ω = 2π×50 = 100π rad/s

RMS ½ Mark

V_rms = v_m/√2 = 311/1.414 ≈ 220 V

Equation 1 Mark

v(t) = 311 sin(100πt) V

V_rms = 220 V, v(t) = 311 sin(100πt)
📋 3 Marks

Q2. A 100 Ω resistor is connected to a 220 V, 50 Hz AC supply. Find (a) RMS current, (b) peak current, (c) power consumed.

(a) RMS current 1 Mark

I_rms = V_rms/R = 220/100 = 2.2 A

(b) Peak current 1 Mark

i_m = I_rms × √2 = 2.2 × 1.414 ≈ 3.11 A

(c) Power 1 Mark

P = V_rms × I_rms = 220 × 2.2 = 484 W
(Also = I²R = 2.2² × 100 = 484 W ✓)

I_rms = 2.2 A, i_m = 3.11 A, P = 484 W
📋 3 Marks

Q3. A 44 mH inductor is connected to 220 V, 50 Hz AC. Find the inductive reactance and RMS current.

Given ½ Mark

L = 44×10⁻³ H, f = 50 Hz, ω = 100π rad/s, V = 220 V

X_L 1 Mark

X_L = ωL = 100π × 44×10⁻³
= 4.4π ≈ 13.82 Ω

Current 1 Mark

I = V/X_L = 220/13.82 ≈ 15.9 A

Power ½ Mark

P = 0 (pure inductor — no real power)

X_L ≈ 13.82 Ω, I ≈ 15.9 A, P = 0
📋 3 Marks

Q4. A 60 μF capacitor is connected to 110 V, 60 Hz AC. Find capacitive reactance and current.

Given ½ Mark

C = 60×10⁻⁶ F, f = 60 Hz, ω = 120π, V = 110 V

X_C 1 Mark

X_C = 1/(ωC) = 1/(120π × 60×10⁻⁶)
= 1/(7.2π×10⁻³)
≈ 44.2 Ω

Current 1 Mark

I = V/X_C = 110/44.2 ≈ 2.49 A

Note ½ Mark

Power = 0 (pure capacitor)

X_C ≈ 44.2 Ω, I ≈ 2.49 A
📋 4 Marks

Q5. A series LCR circuit has R = 20 Ω, L = 1.5 H, C = 35 μF, connected to 200 V variable-frequency supply. Find (a) resonant frequency, (b) impedance at resonance, (c) current at resonance, (d) power at resonance.

(a) Resonant frequency 1½ Marks

ω₀ = 1/√(LC) = 1/√(1.5 × 35×10⁻⁶)
= 1/√(5.25×10⁻⁵)
= 1/(7.25×10⁻³)
≈ 138 rad/s
f₀ ≈ 22 Hz

(b) Impedance at resonance ½ Mark

Z = R = 20 Ω (X_L = X_C, they cancel)

(c) Current at resonance 1 Mark

I = V/R = 200/20 = 10 A

(d) Power 1 Mark

P = I²R = 100 × 20 = 2000 W

ω₀ ≈ 138 rad/s, Z = 20 Ω, I = 10 A, P = 2000 W
📋 4 Marks

Q6. An LCR circuit has R = 40 Ω, X_L = 120 Ω, X_C = 60 Ω. Find Z, phase angle, power factor, and whether the circuit is inductive or capacitive.

Impedance 1 Mark

Z = √(R² + (X_L−X_C)²) = √(40² + 60²)
= √(1600 + 3600) = √5200 ≈ 72.1 Ω

Phase angle 1 Mark

tanφ = (X_L−X_C)/R = 60/40 = 1.5
φ = tan⁻¹(1.5) ≈ 56.3°

Power factor 1 Mark

cosφ = R/Z = 40/72.1 ≈ 0.555

Circuit type 1 Mark

X_L > X_C → inductive. Current LAGS voltage by 56.3°.

Z ≈ 72.1 Ω, φ ≈ 56.3°, PF ≈ 0.555, inductive
📋 3 Marks

Q7. A transformer has 500 primary turns and 5000 secondary turns. Primary connected to 220 V AC. Find (a) secondary voltage, (b) secondary current if primary current is 2 A (ideal).

(a) Secondary voltage 1½ Marks

V_s/V_p = N_s/N_p
V_s = 220 × (5000/500) = 220 × 10 = 2200 V

(b) Secondary current 1 Mark

For ideal transformer: V_p I_p = V_s I_s
220 × 2 = 2200 × I_s
I_s = 440/2200 = 0.2 A

Note ½ Mark

This is a step-up transformer (10× voltage). Current decreased by same factor (10×) — power conserved.

V_s = 2200 V, I_s = 0.2 A
Quick Reference

📐 Complete Formula Sheet

Chapter 7 — All Formulas on One Page

AC Voltage
v = v_m sin(ωt)
RMS Values
V_rms = v_m/√2, I_rms = i_m/√2
Resistor
i_m = v_m/R, φ = 0
Inductive Reactance
X_L = ωL = 2πfL
Capacitive Reactance
X_C = 1/(ωC) = 1/(2πfC)
Impedance (LCR)
Z = √(R² + (X_L − X_C)²)
Current (LCR)
i_m = v_m/Z
Phase Angle
tanφ = (X_L − X_C)/R
Resonant Frequency
ω₀ = 1/√(LC), f₀ = 1/(2π√(LC))
Q-Factor
Q = ω₀L/R = (1/R)√(L/C)
Average Power
P = V_rms I_rms cosφ = I²R
Power Factor
PF = cosφ = R/Z
Transformer Voltage
V_s/V_p = N_s/N_p
Transformer Current
I_s/I_p = N_p/N_s
Power (Transformer)
V_p I_p = V_s I_s (ideal)
Constants
50 Hz India, 60 Hz USA, ω = 2πf

📖 Notation Key

v_m, i_mPeak (maximum) voltage, current
V_rms, I_rmsRMS (effective) values
ωAngular frequency (rad/s) = 2πf
fFrequency (Hz)
TPeriod (s) = 1/f
X_LInductive reactance (Ω)
X_CCapacitive reactance (Ω)
ZImpedance (Ω)
φPhase angle between V and I
ω₀Resonant angular frequency
QQuality factor (dimensionless)
PFPower factor = cosφ
N_p, N_sPrimary, secondary turns
V_p, V_sPrimary, secondary voltages
Test Yourself

✍️ MCQ Practice

Score: 0 / 12
New Pattern

🎯 Assertion–Reason

(A) Both true, R explains A. (B) Both true, R does NOT explain A. (C) A true, R false. (D) A false, R true.

Score: 0 / 6